- This product is protected and cannot be purchased.
- Description
- Additional information
- Reviews (0)
Description
Split clamp bracket to allow installing without removing hubs onto 3” axle tube. Designed to be used for LR chain limiter on stock cars. Clamp can be tighten onto tube or left “floating”. Fits 3/8″ in chain.
(Sold Individually)
Additional information
Chain | With Chain, No Chain |
---|
Be the first to review “Bolt On, Clamp-3″ (Chain Limiter) MAXIMUM” Cancel reply
You may also like…
-
Add to cartQuick View
Bolt On, Caliper Bracket – Small GM (MAXIMUM)
Bolt On, Caliper Bracket (Small GM)
Add to cartQuick View -
Select optionsQuick View
Quick Change Rear End – Bare
Quick Change Rear End With 486 R&P 10″ Alum Spool and Steel Tubes.
Select optionsQuick View -
Add to cartQuick View
Bolt On, Spring Perch – Center (MAXIMUM)
Bolt On, Spring Perch Center
Add to cartQuick View -
Add to cartQuick View
Bolt On, Spring Perch – Offset (MAXIMUM)
Bolt On, Spring Perch Offset
Add to cartQuick View -
Add to cartQuick View
Quick Change Mount, Upper Trailing Arm – w/ “PULL” Bushings – Metric (MAXIMUM)
This bolt on upper trailing arm mount is designed to allow use of a quick change into a stock GM metric chassis. Built with corrected pinion angle and our proven “Pull” Bushings.
NOTE: If installing on a Frankland quick change, the bracket will need to be modified and reinforced to fit.
Add to cartQuick View -
Add to cartQuick View
Bolt On, Trailing Arm Bracket Kit – Multi Hole (MAXIMUM)
Bolt On, Trailing Arm Bracket Kit Multi Hole
Add to cartQuick View -
Select optionsQuick View
Quick Change Rear End – Assembly
Quick Change Rear End Assembly 10″ Alum Spool and Steel Tubes
Select optionsQuick View
Related Products
-
Add to cartQuick View
Bolt, Weight Jack – 11″ Long
1 diameter x 11 long weight jack bolt. (1″-8 Coarse Thread)
Add to cartQuick View -
Add to cartQuick View
Bracket, Caliper (Small GM)
These caliper mount brackets are built to fit the small GM metric calipers. Use this kit to build your own custom rear end.
(Sold Individually)Add to cartQuick View -
Add to cartQuick View
Trailing Arm, Upper – DOGBONE w/ “Pull” Bushing (MAXIMUM)
Want a stronger trailing arm plus the performance advantage of the “Pull” bushing? We proudly give you the “DOGBONE”!
Same length (11-1/8″ C to C) and weight of a stock trailing arm but much stronger. Has “Pull” bushings installed, sized for 1/2″ bolts and is a bolt in ready unit.
(Sold Individually)Add to cartQuick View -
Add to cartQuick View
Cup, Spring – Tapered
These tapered profile spring cups are manufactured from high strength steel and are designed to minimize any stretch and bending while still being lightweight. Has a 1/4″ hole on bottom to allow bolting to your weight jack bolt.
Add to cartQuick View -
Add to cartQuick View
Brackets, Trailing Arm (Single Hole)
Designed for the Wissota street stocks, these trailing arm brackets have the lowest mounting hole position possible. 4.0″ from axle tube to center of hole.
(Sold as a Pair)
Add to cartQuick View -
Add to cartQuick View
Brackets, Trailing Arm (Extreme Drop)
Looking for increased forward bit and traction? Then this trailing arm bracket kit is a must have.
Specifically designed to increase LR drive off the corner and corner entry adjustability with multiple hole adjustments on the RR.
LR bracket is 6.75″ from axle tube to center of bottom hole. (USRA/IMCA Stock Car Legal)
(Sold as a Pair)
Add to cartQuick View -
Add to cartQuick View
Washer, Axle
Stop spending big money on rubber seals and sleeves to stop rear end grease from being pulled into the RH rear end tube. Sold as pair.
Add to cartQuick View -
Add to cartQuick View
Trailing Arm, Lower – BAREBONE (MAXIMUM)
Want a stronger trailing arm at a better price? We proudly give you the “BAREBONE”!
Same length and weight of a stock trailing arm but much stronger. Will accept any OEM type bushing.
(Sold Individually)
Add to cartQuick View -
Add to cartQuick View
Axles, Non-Floater 30″, 5×4 3/4, (31 Spline)
These new Currie 31-spline axles feature press in studs in a 5×4 3/4 wheel bolt pattern, , ¼ thick heavy duty bearing retainer plates, and tapered wheel bearings pressed on.
Add to cartQuick View -
Add to cartQuick View
Trailing Arm, Upper – BAREBONE (MAXIMUM)
Want a stronger trailing arm at a better price? We proudly give you the “BAREBONE”!
Same length and weight of a stock trailing arm but much stronger. Will accept any OEM type bushing.
(Sold Individually)
Add to cartQuick View
Reviews
There are no reviews yet.