Trailing Arm, Lower – BAREBONE (MAXIMUM)
$53.60
Want a stronger trailing arm at a better price? We proudly give you the “BAREBONE”!
Same length and weight of a stock trailing arm but much stronger. Will accept any OEM type bushing.
(Sold Individually)
- Description
- Additional information
- Reviews (0)
Description
Want a stronger trailing arm at a better price? We proudly give you the “BAREBONE”!
Same length and weight of a stock trailing arm but much stronger. Will accept any OEM type bushing.
(Sold Individually)
Additional information
Weight | 6 lbs |
---|---|
Dimensions | 12 × 12 × 12 in |
Be the first to review “Trailing Arm, Lower – BAREBONE (MAXIMUM)” Cancel reply
Related Products
-
Add to cartQuick View
Washer, Axle
Stop spending big money on rubber seals and sleeves to stop rear end grease from being pulled into the RH rear end tube. Sold as pair.
Add to cartQuick View -
Add to cartQuick View
Trailing Arm, Upper – OEM Reproduction w/ “Pull” Bushing
For those of you that want the benefits of the “Pull” bushing but without the hassle of installing them.
OEM reproduction stampings with our bushings installed. Sized for use with a 1/2″ bolt. These are a bolt in ready unit.
(Sold Individually)
Add to cartQuick View -
Add to cartQuick View
Quick Change Mount, Upper Trailing Arm – w/ “PULL” Bushings – Metric (MAXIMUM)
This bolt on upper trailing arm mount is designed to allow use of a quick change into a stock GM metric chassis. Built with corrected pinion angle and our proven “Pull” Bushings.
NOTE: If installing on a Frankland quick change, the bracket will need to be modified and reinforced to fit.
Add to cartQuick View -
Add to cartQuick View
Mount, Upper Trailing Arm – Kit (Ford 9″)
This kit includes two “Pull” bushings, two steel spools, a rectangular mount tube and side gusset bracket. Use this kit to build your own custom rear end.
Add to cartQuick View -
Add to cartQuick View
Brackets, Trailing Arm (Hobby Stock)
Designed for the Hobby stocks, these trailing arm brackets have the lowest mounting hole position possible. 2.50″ from axle tube to center of hole.
(Sold as a Pair)
Add to cartQuick View -
Add to cartQuick View
Brackets, Trailing Arm (Extreme Drop)
Looking for increased forward bit and traction? Then this trailing arm bracket kit is a must have.
Specifically designed to increase LR drive off the corner and corner entry adjustability with multiple hole adjustments on the RR.
LR bracket is 6.75″ from axle tube to center of bottom hole. (USRA/IMCA Stock Car Legal)
(Sold as a Pair)
Add to cartQuick View -
Add to cartQuick View
Axles, Non-Floater 30″, 5×5, (28 or 31 Spline)
These new Superior 28 or 31-spline axles feature screw in studs in a 5×5 wheel bolt pattern, , ¼ thick heavy duty bearing retainer plates, and tapered wheel bearings pressed on.
Add to cartQuick View -
Add to cartQuick View
Clamp, Limit Chain (1-1/2” Tube) – Wehrs
1-1/2” Tube Diameter Clamp For Limit Chains on Chassis Side
Add to cartQuick View -
Add to cartQuick View
Axle, 29.5″ GN Gun Drilled (31 Spline)
29.5″ Premium GN gun drilled axle.
Add to cartQuick View -
Add to cartQuick View
Rear End Brace Kit – 60″
This kit is design to reinforce the rear end so that the tubes do not bend if a wheel gets wrecked.
It will also prevent the rear end from deflecting under load and changing the alignment of the rear end while braking and under gas.(USRA Legal)
Add to cartQuick View
Reviews
There are no reviews yet.