Trailing Arm, Upper – BAREBONE (MAXIMUM)
$51.00
Want a stronger trailing arm at a better price? We proudly give you the “BAREBONE”!
Same length and weight of a stock trailing arm but much stronger. Will accept any OEM type bushing.
(Sold Individually)
- Description
- Additional information
- Reviews (0)
Description
Want a stronger trailing arm at a better price? We proudly give you the “BAREBONE”!
Same length and weight of a stock trailing arm but much stronger. Will accept any OEM type bushing.
(Sold Individually)
Additional information
Weight | 6 lbs |
---|---|
Dimensions | 12 × 12 × 12 in |
Be the first to review “Trailing Arm, Upper – BAREBONE (MAXIMUM)” Cancel reply
You may also like…
-
Add to cartQuick View
Trailing Arm, Lower – BAREBONE (MAXIMUM)
Want a stronger trailing arm at a better price? We proudly give you the “BAREBONE”!
Same length and weight of a stock trailing arm but much stronger. Will accept any OEM type bushing.
(Sold Individually)
Add to cartQuick View
Related Products
-
Add to cartQuick View
Brackets, Trailing Arm (Single Hole)
Designed for the Wissota street stocks, these trailing arm brackets have the lowest mounting hole position possible. 4.0″ from axle tube to center of hole.
(Sold as a Pair)
Add to cartQuick View -
Add to cartQuick View
Trailing Arm, Upper – DOGBONE w/ “Pull” Bushing (MAXIMUM)
Want a stronger trailing arm plus the performance advantage of the “Pull” bushing? We proudly give you the “DOGBONE”!
Same length (11-1/8″ C to C) and weight of a stock trailing arm but much stronger. Has “Pull” bushings installed, sized for 1/2″ bolts and is a bolt in ready unit.
(Sold Individually)Add to cartQuick View -
Add to cartQuick View
Quick Change Mount, Upper Trailing Arm – w/ “PULL” Bushings – Metric (MAXIMUM)
This bolt on upper trailing arm mount is designed to allow use of a quick change into a stock GM metric chassis. Built with corrected pinion angle and our proven “Pull” Bushings.
NOTE: If installing on a Frankland quick change, the bracket will need to be modified and reinforced to fit.
Add to cartQuick View -
Add to cartQuick View
Assembly, Rear End Housing – 60″ GN (L3) w/ Sport Mod Jigged
60″ offset new reproduction stamping Ford 9″ housing with new 3″ tubes and GN hub type snouts. Housings have fill and drain plug installed. Kit includes standard 5×5 GN hubs, hub bearings, seals, brake rotor, drive flange, 31 spline solid axles and all hardware necessary.
Spring Perchs & Brake Caliper Brackets are now Bolt-On Accessories (not included in Rear End Assembly Price)
Add to cartQuick View -
Add to cartQuick View
Clamp, Limit Chain (1-1/2” Tube) – Wehrs
1-1/2” Tube Diameter Clamp For Limit Chains on Chassis Side
Add to cartQuick View -
Add to cartQuick View
Axle, 29.5″ GN Gun Drilled (31 Spline)
29.5″ Premium GN gun drilled axle.
Add to cartQuick View -
Add to cartQuick View
Washer, Axle
Stop spending big money on rubber seals and sleeves to stop rear end grease from being pulled into the RH rear end tube. Sold as pair.
Add to cartQuick View -
Add to cartQuick View
Axle, 32″ GN Gun Drilled (31 Spline)
29.5″ Premium GN gun drilled axle.
Add to cartQuick View -
Add to cartQuick View
Mount, Upper Trailing Arm – Kit (Ford 9″)
This kit includes two “Pull” bushings, two steel spools, a rectangular mount tube and side gusset bracket. Use this kit to build your own custom rear end.
Add to cartQuick View -
Add to cartQuick View
Trailing Arm, Upper – OEM Reproduction w/ “Pull” Bushing
For those of you that want the benefits of the “Pull” bushing but without the hassle of installing them.
OEM reproduction stampings with our bushings installed. Sized for use with a 1/2″ bolt. These are a bolt in ready unit.
(Sold Individually)
Add to cartQuick View
Reviews
There are no reviews yet.