



Bolt On, Clamp – 3″ ID (MAXIMUM)
$55.99
- Description
Description
Split trailing arm bracket clamp design to allow installing without removing hubs onto 3” axle tube.
3.75″ wide
Hardware included
sold individually
Related Products
-
Add to cartQuick View
Rear End Brace Kit – 60″
This kit is design to reinforce the rear end so that the tubes do not bend if a wheel gets wrecked.
It will also prevent the rear end from deflecting under load and changing the alignment of the rear end while braking and under gas.(USRA Legal)
Add to cartQuick View -
Add to cartQuick View
Brackets, Trailing Arm – HEAVY, Slotted (LR ONLY)
Designed for stock cars with a 7.5″ max trailing arm length.
This trailing arm bracket use common offset slugs (sold separately) to allow you to change the amount of lead or trail in the rear end. Simply replace the slug with different combination of offset slugs. Tack weld the slugs to secure them to the trailing arm.
This bracket is also built heavy, weigh 7.5lbs (with slugs) to help increase LR rear end weight.
Perfect for the guys that already have or Extreme or Xtrmer Drop brackets. Simply replace the LR bracket and have increase drive and adjustability.
(Sold individually)
(Slugs sold separately)
Add to cartQuick View -
Add to cartQuick View
Bracket, Caliper (Small GM)
These caliper mount brackets are built to fit the small GM metric calipers. Use this kit to build your own custom rear end.
(Sold Individually)Add to cartQuick View -
Add to cartQuick View
Brackets, Trailing Arm (Extreme Drop)
Looking for increased forward bit and traction? Then this trailing arm bracket kit is a must have.
Specifically designed to increase LR drive off the corner and corner entry adjustability with multiple hole adjustments on the RR.
LR bracket is 6.75″ from axle tube to center of bottom hole. (USRA/IMCA Stock Car Legal)
(Sold as a Pair)
Add to cartQuick View -
Add to cartQuick View
Clamp, Limit Chain (1-1/2” Tube) – Wehrs
1-1/2” Tube Diameter Clamp For Limit Chains on Chassis Side
Add to cartQuick View -
Add to cartQuick View
Cup, Spring – Tapered
These tapered profile spring cups are manufactured from high strength steel and are designed to minimize any stretch and bending while still being lightweight. Has a 1/4″ hole on bottom to allow bolting to your weight jack bolt.
Add to cartQuick View -
Add to cartQuick View
Brackets, Trailing Arm (Multi-Hole)
This trailing arm bracket kit was designed to allow trailing arm angle adjustments just like what can be done on modifieds…..
(Sold as a Pair)
Add to cartQuick View -
Add to cartQuick View
Assembly, Rear End Housing – 60″ GN (L3) w/ Sport Mod Jigged
60″ offset new reproduction stamping Ford 9″ housing with new 3″ tubes and GN hub type snouts. Housings have fill and drain plug installed. Kit includes standard 5×5 GN hubs, hub bearings, seals, brake rotor, drive flange, 31 spline solid axles and all hardware necessary.
Spring Perchs & Brake Caliper Brackets are now Bolt-On Accessories (not included in Rear End Assembly Price)
Add to cartQuick View -
Add to cartQuick View
Axles, Non-Floater 30″, 5×5, (28 or 31 Spline)
These new Superior 28 or 31-spline axles feature screw in studs in a 5×5 wheel bolt pattern, , ¼ thick heavy duty bearing retainer plates, and tapered wheel bearings pressed on.
Add to cartQuick View -
Add to cartQuick View
Trailing Arm, Upper – DOGBONE w/ “Pull” Bushing (MAXIMUM)
Want a stronger trailing arm plus the performance advantage of the “Pull” bushing? We proudly give you the “DOGBONE”!
Same length (11-1/8″ C to C) and weight of a stock trailing arm but much stronger. Has “Pull” bushings installed, sized for 1/2″ bolts and is a bolt in ready unit.
(Sold Individually)Add to cartQuick View