Brackets, Trailing Arm (Hobby Stock)
$50.40
Designed for the Hobby stocks, these trailing arm brackets have the lowest mounting hole position possible. 2.50″ from axle tube to center of hole.
(Sold as a Pair)
- Description
- Additional information
Description
Designed for the Hobby stocks, these trailing arm brackets have the lowest mounting hole position possible. 2.50″ from axle tube to center of hole.
(Sold as a Pair)
Additional information
| Weight | 5 lbs |
|---|---|
| Dimensions | 12 × 12 × 12 in |
Related Products
-
Add to cartQuick ViewAxles, Non-Floater 30″, 5×4 3/4, (31 Spline)
$325.00These new Currie 31-spline axles feature press in studs in a 5×4 3/4 wheel bolt pattern, , ¼ thick heavy duty bearing retainer plates, and tapered wheel bearings pressed on.
Add to cartQuick View -
Add to cartQuick ViewBRACKET, CHASSIS PANHARD, BOLT ON – 3 INCH OFFSET (PAIR)
$50.00BRACKET, CHASSIS PANHARD, BOLT ON – 3 INCH OFFSET (PAIR)
Add to cartQuick View -
Add to cartQuick ViewBrackets, Trailing Arm (Single Hole)
$50.40Designed for the Wissota street stocks, these trailing arm brackets have the lowest mounting hole position possible. 4.0″ from axle tube to center of hole.
(Sold as a Pair)
Add to cartQuick View -
Add to cartQuick ViewRear End Brace Kit – 60″
$119.94This kit is design to reinforce the rear end so that the tubes do not bend if a wheel gets wrecked.
It will also prevent the rear end from deflecting under load and changing the alignment of the rear end while braking and under gas.(USRA Legal)
Add to cartQuick View -
Add to cartQuick ViewAssembly, Rear End Housing – 60″ GN (L3) w/ Sport Mod Jigged
$1,538.4660″ offset new reproduction stamping Ford 9″ housing with new 3″ tubes and GN hub type snouts. Housings have fill and drain plug installed. Kit includes standard 5×5 GN hubs, hub bearings, seals, brake rotor, drive flange, 31 spline solid axles and all hardware necessary.
Spring Perchs & Brake Caliper Brackets are now Bolt-On Accessories (not included in Rear End Assembly Price)
Add to cartQuick View -
Add to cartQuick ViewClamp, Limit Chain (1-1/2” Tube) – Wehrs
$25.001-1/2” Tube Diameter Clamp For Limit Chains on Chassis Side
Add to cartQuick View -
Add to cartQuick ViewWasher, Axle
$5.60Stop spending big money on rubber seals and sleeves to stop rear end grease from being pulled into the RH rear end tube. Sold as pair.
Add to cartQuick View -
Add to cartQuick ViewQuick Change Mount, Upper Trailing Arm – w/ “SPHERICAL” Bushings – Metric (MAXIMUM)
$166.99This bolt on upper trailing arm mount is designed to allow use of a quick change into a stock GM metric chassis. Built with corrected pinion angle and our proven “Spherical” Bushings.
NOTE: If installing on a Frankland quick change, the bracket will need to be modified and reinforced to fit.
Add to cartQuick View -
Add to cartQuick ViewBracket, Caliper (Small GM)
$12.50These caliper mount brackets are built to fit the small GM metric calipers. Use this kit to build your own custom rear end.
(Sold Individually)Add to cartQuick View -
Add to cartQuick ViewBrackets, Trailing Arm (Multi-Hole)
$84.00This trailing arm bracket kit was designed to allow trailing arm angle adjustments just like what can be done on modifieds…..
(Sold as a Pair)
Add to cartQuick View
