SEAL, GN HUB SEAL 3X3.75X.38
$11.99
GN Hub Seal. Used on inside of all standard GN hubs.
- Description
Description
GN Hub Seal. Used on inside of all standard GN hubs.
You may also like…
-
Add to cartQuick ViewAssembly, Rear End Housing – 60″ GN (L3) w/ Sport Mod Jigged
$1,538.4660″ offset new reproduction stamping Ford 9″ housing with new 3″ tubes and GN hub type snouts. Housings have fill and drain plug installed. Kit includes standard 5×5 GN hubs, hub bearings, seals, brake rotor, drive flange, 31 spline solid axles and all hardware necessary.
Spring Perchs & Brake Caliper Brackets are now Bolt-On Accessories (not included in Rear End Assembly Price)
Add to cartQuick View -
Add to cartQuick ViewSeal, Axle Housing (Inner)
$61.99Axle Housing Inner Seal for 9 Inch GN Rearends. Three O-rings that seal it to the axle tube and two bonded, heavy duty inner seals designed to compensate for any amount of axle shaft run out. Keeps gear oil in the center section. 2.625″ Housing Tube Size.
Add to cartQuick View
Related Products
-
Add to cartQuick ViewAxles, Non-Floater 30″, 5×5, (28 or 31 Spline)
$325.00These new Superior 28 or 31-spline axles feature screw in studs in a 5×5 wheel bolt pattern, , ¼ thick heavy duty bearing retainer plates, and tapered wheel bearings pressed on.
Add to cartQuick View -
Add to cartQuick ViewTrailing Arm, Upper – BAREBONE (MAXIMUM)
$65.00Want a stronger trailing arm at a better price? We proudly give you the “BAREBONE”!
Same length and weight of a stock trailing arm but much stronger. Will accept any OEM type bushing.
(Sold Individually)
Add to cartQuick View -
Add to cartQuick ViewBushing, “PULL” (Trailing Arms)
$35.75This is a new bushing that is used in the upper & lower trailing arms to create side bite and cushioning of the rear end.
Sold individually
Add to cartQuick View -
Add to cartQuick ViewAxle, 32″ GN Gun Drilled (31 Spline)
$199.5029.5″ Premium GN gun drilled axle.
Add to cartQuick View -
Add to cartQuick ViewBrackets, Trailing Arm (Hobby Stock)
$50.40Designed for the Hobby stocks, these trailing arm brackets have the lowest mounting hole position possible. 2.50″ from axle tube to center of hole.
(Sold as a Pair)
Add to cartQuick View -
Add to cartQuick ViewBrackets, Trailing Arm (Single Hole)
$50.40Designed for the Wissota street stocks, these trailing arm brackets have the lowest mounting hole position possible. 4.0″ from axle tube to center of hole.
(Sold as a Pair)
Add to cartQuick View -
Add to cartQuick View
Axle, 29.5″ GN Gun Drilled (31 Spline)
$199.5029.5″ Premium GN gun drilled axle.
Add to cartQuick View -
Add to cartQuick ViewBolt, Weight Jack – 11″ Long
$21.991 diameter x 11 long weight jack bolt. (1″-8 Coarse Thread)
Add to cartQuick View -
Add to cartQuick ViewTrailing Arm, Lower – BAREBONE (MAXIMUM)
$53.60Want a stronger trailing arm at a better price? We proudly give you the “BAREBONE”!
Same length and weight of a stock trailing arm but much stronger. Will accept any OEM type bushing.
(Sold Individually)
Add to cartQuick View -
Add to cartQuick ViewBrackets, Trailing Arm (Extreme Drop)
$112.00Looking for increased forward bit and traction? Then this trailing arm bracket kit is a must have.
Specifically designed to increase LR drive off the corner and corner entry adjustability with multiple hole adjustments on the RR.
LR bracket is 6.75″ from axle tube to center of bottom hole. (USRA/IMCA Stock Car Legal)
(Sold as a Pair)
Add to cartQuick View
