BRACKET, TRAILING ARM (MULTI-HOLE) – RR ONLY
$50.00
RR multi hole trailing arm bracket only.
- Description
Description
RR multi hole trailing arm bracket only.
The bolt holes are radiused so that when installed properly onto the rear end when you make a trailing arm angle adjustment you do not affect the wheelbase.
Lowest hole on both brackets is 5.25″ from bottom of axle tube to bolt hole center.
.625″ between each hole.
You may also like…
-
Add to cartQuick ViewBrackets, Trailing Arm (Multi-Hole)
$84.00This trailing arm bracket kit was designed to allow trailing arm angle adjustments just like what can be done on modifieds…..
(Sold as a Pair)
Add to cartQuick View
Related Products
-
Add to cartQuick ViewAssembly, Rear End Housing – 60″ GN (L3) w/ Sport Mod Jigged
$1,538.4660″ offset new reproduction stamping Ford 9″ housing with new 3″ tubes and GN hub type snouts. Housings have fill and drain plug installed. Kit includes standard 5×5 GN hubs, hub bearings, seals, brake rotor, drive flange, 31 spline solid axles and all hardware necessary.
Spring Perchs & Brake Caliper Brackets are now Bolt-On Accessories (not included in Rear End Assembly Price)
Add to cartQuick View -
Add to cartQuick ViewTrailing Arm, Upper – BAREBONE (MAXIMUM)
$65.00Want a stronger trailing arm at a better price? We proudly give you the “BAREBONE”!
Same length and weight of a stock trailing arm but much stronger. Will accept any OEM type bushing.
(Sold Individually)
Add to cartQuick View -
Add to cartQuick ViewWasher, Axle
$5.60Stop spending big money on rubber seals and sleeves to stop rear end grease from being pulled into the RH rear end tube. Sold as pair.
Add to cartQuick View -
Add to cartQuick ViewRear End Brace Kit (Main Bracket Only)
$18.98This is the main bracket for the “Rear End Brace Kits” (sold individually)
Add to cartQuick View -
Add to cartQuick View
Brackets, Trailing Arm (Multi-Hole)
$84.00This trailing arm bracket kit was designed to allow trailing arm angle adjustments just like what can be done on modifieds…..
(Sold as a Pair)
Add to cartQuick View -
Add to cartQuick ViewBolt, Weight Jack – 11″ Long
$21.991 diameter x 11 long weight jack bolt. (1″-8 Coarse Thread)
Add to cartQuick View -
Add to cartQuick ViewTrailing Arm, Upper – DOGBONE w/ “Pull” Bushing (MAXIMUM)
$109.50Want a stronger trailing arm plus the performance advantage of the “Pull” bushing? We proudly give you the “DOGBONE”!
Same length (11-1/8″ C to C) and weight of a stock trailing arm but much stronger. Has “Pull” bushings installed, sized for 1/2″ bolts and is a bolt in ready unit.
(Sold Individually)Add to cartQuick View -
Add to cartQuick ViewHousing, Rear End – 60″ GN (L3) w/ Sport Mod Jigged
$901.3860″ offset new reproduction stamping Ford 9″ housing with new 3″ tubes and GN hub type snouts. Housings have fill and drain plug installed. SportMod jigged.
Spring Perchs & Brake Caliper Brackets are now Bolt-On Accessories (not included in Rear End Housing Price)
(IMCA Legal)
Custom Part is Non-Returnable and Non-Refundable.
Add to cartQuick View -
Add to cartQuick ViewRear End Brace Kit – 60″
$119.94This kit is design to reinforce the rear end so that the tubes do not bend if a wheel gets wrecked.
It will also prevent the rear end from deflecting under load and changing the alignment of the rear end while braking and under gas.(USRA Legal)
Add to cartQuick View -
Add to cartQuick ViewBrackets, Trailing Arm (Extreme Drop)
$112.00Looking for increased forward bit and traction? Then this trailing arm bracket kit is a must have.
Specifically designed to increase LR drive off the corner and corner entry adjustability with multiple hole adjustments on the RR.
LR bracket is 6.75″ from axle tube to center of bottom hole. (USRA/IMCA Stock Car Legal)
(Sold as a Pair)
Add to cartQuick View
