Spacer, 5/8″ High Misalignment – 3/4″ Long
$8.75
5/8” high misalignment spacer 1/2″ ID 3/4” long. Measured from end of spacer to the heim.
- Measurement is not total overall length.
- Description
Description
5/8” high misalignment spacer 1/2″ ID 3/4” long. Measured from end of spacer to the heim.
- Measurement is not total overall length.
Related Products
-
Add to cartQuick ViewAxles, Non-Floater 30″, 5×5, (28 or 31 Spline)
$325.00These new Superior 28 or 31-spline axles feature screw in studs in a 5×5 wheel bolt pattern, , ¼ thick heavy duty bearing retainer plates, and tapered wheel bearings pressed on.
Add to cartQuick View -
Add to cartQuick ViewBolt On, Trailing Arm Bracket Kit – HEAVY, Single Hole LR ONLY (MAXIMUM)
$156.00Bolt On, Trailing Arm Bracket Kit – HEAVY, Single Hole (LR Only)
Add to cartQuick View -
Add to cartQuick ViewBrackets, Trailing Arm (Multi-Hole)
$84.00This trailing arm bracket kit was designed to allow trailing arm angle adjustments just like what can be done on modifieds…..
(Sold as a Pair)
Add to cartQuick View -
Add to cartQuick View
Axles, Non-Floater 30″, 5×4 3/4, (31 Spline)
$325.00These new Currie 31-spline axles feature press in studs in a 5×4 3/4 wheel bolt pattern, , ¼ thick heavy duty bearing retainer plates, and tapered wheel bearings pressed on.
Add to cartQuick View -
Add to cartQuick ViewBushing, “PULL” (Trailing Arms)
$35.75This is a new bushing that is used in the upper & lower trailing arms to create side bite and cushioning of the rear end.
Sold individually
Add to cartQuick View -
Add to cartQuick ViewAxle, 32″ GN Gun Drilled (31 Spline)
$199.5029.5″ Premium GN gun drilled axle.
Add to cartQuick View -
Add to cartQuick ViewAssembly, Rear End Housing – 60″ GN (L3) w/ Sport Mod Jigged
$1,538.4660″ offset new reproduction stamping Ford 9″ housing with new 3″ tubes and GN hub type snouts. Housings have fill and drain plug installed. Kit includes standard 5×5 GN hubs, hub bearings, seals, brake rotor, drive flange, 31 spline solid axles and all hardware necessary.
Spring Perchs & Brake Caliper Brackets are now Bolt-On Accessories (not included in Rear End Assembly Price)
Add to cartQuick View -
Add to cartQuick ViewQuick Change Mount, Upper Trailing Arm – w/ “PULL” Bushings – Metric (MAXIMUM)
$125.50This bolt on upper trailing arm mount is designed to allow use of a quick change into a stock GM metric chassis. Built with corrected pinion angle and our proven “Pull” Bushings.
NOTE: If installing on a Frankland quick change, the bracket will need to be modified and reinforced to fit.
Add to cartQuick View -
Add to cartQuick ViewBrackets, Trailing Arm (Extreme Drop)
$112.00Looking for increased forward bit and traction? Then this trailing arm bracket kit is a must have.
Specifically designed to increase LR drive off the corner and corner entry adjustability with multiple hole adjustments on the RR.
LR bracket is 6.75″ from axle tube to center of bottom hole. (USRA/IMCA Stock Car Legal)
(Sold as a Pair)
Add to cartQuick View -
Add to cartQuick ViewPerch, Spring Kit (Offset or Centered)
$31.98Strong, simple and lightweight spring perches that you can use to build your custom rear end. (sold as a pair)
Add to cartQuick View
