Trailing Arm, Upper – DOGBONE w/ “Pull” Bushing (MAXIMUM)
$98.50
Want a stronger trailing arm plus the performance advantage of the “Pull” bushing? We proudly give you the “DOGBONE”!
Same length (11-1/8″ C to C) and weight of a stock trailing arm but much stronger. Has “Pull” bushings installed, sized for 1/2″ bolts and is a bolt in ready unit.
(Sold Individually)
- Description
Description
Want a stronger trailing arm plus the performance advantage of the “Pull” bushing? We proudly give you the “DOGBONE”!
Same length (11-1/8″ C to C) and weight of a stock trailing arm but much stronger. Has “Pull” bushings installed, sized for 1/2″ bolts and is a bolt in ready unit.
(Sold Individually)
You may also like…
-
Add to cartQuick ViewBushing, “PULL” (Trailing Arms)
$30.75This is a new bushing that is used in the upper & lower trailing arms to create side bite and cushioning of the rear end.
Sold individually
Add to cartQuick View
Related Products
-
Add to cartQuick ViewBolt, Weight Jack – 11″ Long
$21.991 diameter x 11 long weight jack bolt. (1″-8 Coarse Thread)
Add to cartQuick View -
Add to cartQuick ViewBrackets, Trailing Arm (Hobby Stock)
$50.40Designed for the Hobby stocks, these trailing arm brackets have the lowest mounting hole position possible. 2.50″ from axle tube to center of hole.
(Sold as a Pair)
Add to cartQuick View -
Add to cartQuick ViewAxles, Non-Floater 30″, 5×4 3/4, (31 Spline)
$325.00These new Currie 31-spline axles feature press in studs in a 5×4 3/4 wheel bolt pattern, , ¼ thick heavy duty bearing retainer plates, and tapered wheel bearings pressed on.
Add to cartQuick View -
Add to cartQuick ViewTrailing Arm, Upper – OEM Reproduction w/ “Pull” Bushing
$130.50For those of you that want the benefits of the “Pull” bushing but without the hassle of installing them.
OEM reproduction stampings with our bushings installed. Sized for use with a 1/2″ bolt. These are a bolt in ready unit.
(Sold Individually)
Add to cartQuick View -
Add to cartQuick ViewWasher, Axle
$5.60Stop spending big money on rubber seals and sleeves to stop rear end grease from being pulled into the RH rear end tube. Sold as pair.
Add to cartQuick View -
Add to cartQuick ViewTrailing Arm, Lower – BAREBONE (MAXIMUM)
$53.60Want a stronger trailing arm at a better price? We proudly give you the “BAREBONE”!
Same length and weight of a stock trailing arm but much stronger. Will accept any OEM type bushing.
(Sold Individually)
Add to cartQuick View -
Add to cartQuick ViewCup, Spring – Tapered
$13.38These tapered profile spring cups are manufactured from high strength steel and are designed to minimize any stretch and bending while still being lightweight. Has a 1/4″ hole on bottom to allow bolting to your weight jack bolt.
Add to cartQuick View -
Add to cartQuick ViewBolt On, Trailing Arm Bracket Kit – HEAVY, Single Hole LR ONLY (MAXIMUM)
$156.00Bolt On, Trailing Arm Bracket Kit – HEAVY, Single Hole (LR Only)
Add to cartQuick View -
Add to cartQuick ViewClamp, Limit Chain (1-1/2” Tube) – Wehrs
$25.001-1/2” Tube Diameter Clamp For Limit Chains on Chassis Side
Add to cartQuick View -
Add to cartQuick ViewBrackets, Trailing Arm (Extreme Drop)
$112.00Looking for increased forward bit and traction? Then this trailing arm bracket kit is a must have.
Specifically designed to increase LR drive off the corner and corner entry adjustability with multiple hole adjustments on the RR.
LR bracket is 6.75″ from axle tube to center of bottom hole. (USRA/IMCA Stock Car Legal)
(Sold as a Pair)
Add to cartQuick View
