Mount, Upper Trailing Arm – Kit (Ford 9″)
$89.00
This kit includes two “Pull” bushings, two steel spools, a rectangular mount tube and side gusset bracket. Use this kit to build your own custom rear end.
- Description
- Reviews (0)
Description
This kit includes two “Pull” bushings, two steel spools, a rectangular mount tube and side gusset bracket. Use this kit to build your own custom rear end.
Be the first to review “Mount, Upper Trailing Arm – Kit (Ford 9″)”
Related Products
-
Add to cartQuick ViewBrackets, Trailing Arm (Multi-Hole)
$84.00This trailing arm bracket kit was designed to allow trailing arm angle adjustments just like what can be done on modifieds…..
(Sold as a Pair)
Add to cartQuick View -
Add to cartQuick ViewHousing, Rear End – 60″ GN (L3) w/ Sport Mod Jigged
$889.2060″ offset new reproduction stamping Ford 9″ housing with new 3″ tubes and GN hub type snouts. Housings have fill and drain plug installed. SportMod jigged.
(IMCA Legal)
Custom Part is Non-Returnable and Non-Refundable.
Add to cartQuick View -
Add to cartQuick ViewBrackets, Trailing Arm (Extreme Drop)
$112.00Looking for increased forward bit and traction? Then this trailing arm bracket kit is a must have.
Specifically designed to increase LR drive off the corner and corner entry adjustability with multiple hole adjustments on the RR.
LR bracket is 6.75″ from axle tube to center of bottom hole. (USRA/IMCA Stock Car Legal)
(Sold as a Pair)
Add to cartQuick View -
Add to cartQuick ViewBracket, Caliper (Small GM)
$11.20These caliper mount brackets are built to fit the small GM metric calipers. Use this kit to build your own custom rear end.
(Sold Individually)Add to cartQuick View -
Add to cartQuick ViewAxle, 29.5″ GN Gun Drilled (31 Spline)
$199.5029.5″ Premium GN gun drilled axle.
Add to cartQuick View -
Add to cartQuick ViewUpgrade, Gun Drilled Axles for Assembly, Rear End Housing (MMX401-60R1104)
$199.5029.5″ and 32″ Pair of premium GN gun drilled axles.
(Only available when purchasing rear end assembly MMX 401-60R1104)
Add to cartQuick View -
Add to cartQuick ViewBushing, “PULL” (Trailing Arms)
$28.22This is a new bushing that is used in the upper & lower trailing arms to create side bite and cushioning of the rear end.
Sold individually
Add to cartQuick View -
Add to cartQuick ViewBrackets, Trailing Arm (Hobby Stock)
$50.40Designed for the Hobby stocks, these trailing arm brackets have the lowest mounting hole position possible. 2.50″ from axle tube to center of hole.
(Sold as a Pair)
Add to cartQuick View -
Add to cartQuick ViewRear End Brace Kit – 60″
$111.94This kit is design to reinforce the rear end so that the tubes do not bend if a wheel gets wrecked.
It will also prevent the rear end from deflecting under load and changing the alignment of the rear end while braking and under gas.(USRA Legal)
Add to cartQuick View -
Add to cartQuick ViewHousing, Rear End – 60″ Non Floater IMCA Hobby Stock Jigged
$780.90New reproduction stamping Ford 9″ housing with new 3″ tubes and big bearing type flanges.
Jigged with our:
– Lower trailing arm mounts
– Upper “Pull” bushing mounts
– Spring perches
– Shock mounts(IMCA Approved)
Custom Part is Non-Returnable and Non-Refundable.
Add to cartQuick View
Reviews
There are no reviews yet.