MOUNT, PANHARD BAR – (3 LINK CLIMBER) WEHRS
$145.00
Panhard bar mount used on chassis side of Medieval modifieds and sport mods.
- Description
Description
Panhard bar mount used on chassis side of Medieval modifieds and sport mods.
Fits 2 x 2 square tube.
Steel material. Coated black.
Fits standard 3/4″ heim panhard and J-bars
You may also like…
-
Add to cartQuick ViewMOUNT, PANHARD BAR – (3 HOLE 2X2) WEHRS
$66.00Panhard bar mount used on chassis side of Medieval modifieds and sport mods.
Add to cartQuick View -
Add to cartQuick ViewMount, Pinion Panhard 9″ Ford (Right Side Climber, Steel)
$130.00MAXIMUM Performance right side climbing panhard mount for Ford 9″ rear ends. (Steel)
Mounts J-Bar to 9″ third-member – 4 3/8″ offset from pinion.
Add to cartQuick View -
Add to cartQuick ViewMount, Pinion Panhard QC (Right Side Climber, Steel)
$130.00MAXIMUM Performance right side climbing panhard mount for quick change rear ends. (Steel)
Mounts J-Bar to QC rear end – 4 3/8″ offset from pinion.
Add to cartQuick View
Related Products
-
Add to cartQuick ViewBRACKET, CHASSIS PANHARD, BOLT ON – 3 INCH OFFSET (PAIR)
$50.00BRACKET, CHASSIS PANHARD, BOLT ON – 3 INCH OFFSET (PAIR)
Add to cartQuick View -
Add to cartQuick ViewBolt On, Trailing Arm Bracket Kit – HEAVY, Single Hole LR ONLY (MAXIMUM)
$156.00Bolt On, Trailing Arm Bracket Kit – HEAVY, Single Hole (LR Only)
Add to cartQuick View -
Add to cartQuick ViewMount, Upper Trailing Arm – Kit (Ford 9″)
$103.00This kit includes two “Pull” bushings, two steel spools, a rectangular mount tube and side gusset bracket. Use this kit to build your own custom rear end.
Add to cartQuick View -
Add to cartQuick ViewRear End Brace Kit – 60″
$119.94This kit is design to reinforce the rear end so that the tubes do not bend if a wheel gets wrecked.
It will also prevent the rear end from deflecting under load and changing the alignment of the rear end while braking and under gas.(USRA Legal)
Add to cartQuick View -
Add to cartQuick ViewWasher, Axle
$5.60Stop spending big money on rubber seals and sleeves to stop rear end grease from being pulled into the RH rear end tube. Sold as pair.
Add to cartQuick View -
Add to cartQuick ViewBushing, “PULL” (Trailing Arms)
$35.75This is a new bushing that is used in the upper & lower trailing arms to create side bite and cushioning of the rear end.
Sold individually
Add to cartQuick View -
Add to cartQuick ViewBolt, Weight Jack – 11″ Long
$21.991 diameter x 11 long weight jack bolt. (1″-8 Coarse Thread)
Add to cartQuick View -
Add to cartQuick ViewBushing, “SPHERICAL” – Trailing Arm (MAXIMUM)
$44.95MAXIMUM Spherical Bushing
Sold individually
Add to cartQuick View -
Add to cartQuick ViewAxles, Non-Floater 30″, 5×4 3/4, (31 Spline)
$325.00These new Currie 31-spline axles feature press in studs in a 5×4 3/4 wheel bolt pattern, , ¼ thick heavy duty bearing retainer plates, and tapered wheel bearings pressed on.
Add to cartQuick View -
Add to cartQuick ViewRear End Brace Kit (Main Bracket Only)
$18.98This is the main bracket for the “Rear End Brace Kits” (sold individually)
Add to cartQuick View
