Mount, Pinion Panhard 9″ Ford (Right Side Climber, Steel)
$130.00
MAXIMUM Performance right side climbing panhard mount for Ford 9″ rear ends. (Steel)
Mounts J-Bar to 9″ third-member – 4 3/8″ offset from pinion.
- Description
Description
MAXIMUM Performance right side climbing panhard mount for Ford 9″ rear ends. (Steel)
Mounts J-Bar to Ford 9″ third member – 4 3/8″ offset from pinion.
Lightest weight pinion mount in the industry.
Laser cut out of high strength Grade 50 steel for strength and durability.
Kit includes climbing gear and hardware needed for J-bar.
You may also like…
-
Add to cartQuick ViewMount, Pinion Panhard QC (Right Side Climber, Steel)
$130.00MAXIMUM Performance right side climbing panhard mount for quick change rear ends. (Steel)
Mounts J-Bar to QC rear end – 4 3/8″ offset from pinion.
Add to cartQuick View
Related Products
-
Add to cartQuick ViewBrackets, Trailing Arm (Extreme Drop)
$112.00Looking for increased forward bit and traction? Then this trailing arm bracket kit is a must have.
Specifically designed to increase LR drive off the corner and corner entry adjustability with multiple hole adjustments on the RR.
LR bracket is 6.75″ from axle tube to center of bottom hole. (USRA/IMCA Stock Car Legal)
(Sold as a Pair)
Add to cartQuick View -
Add to cartQuick ViewTrailing Arm, Upper – BAREBONE (MAXIMUM)
$65.00Want a stronger trailing arm at a better price? We proudly give you the “BAREBONE”!
Same length and weight of a stock trailing arm but much stronger. Will accept any OEM type bushing.
(Sold Individually)
Add to cartQuick View -
Add to cartQuick ViewMount, Upper Trailing Arm – Kit (Ford 9″)
$103.00This kit includes two “Pull” bushings, two steel spools, a rectangular mount tube and side gusset bracket. Use this kit to build your own custom rear end.
Add to cartQuick View -
Add to cartQuick ViewBushing, “SPHERICAL” – Trailing Arm (MAXIMUM)
$44.95MAXIMUM Spherical Bushing
Sold individually
Add to cartQuick View -
Add to cartQuick ViewTrailing Arm, Upper – DOGBONE w/ “Pull” Bushing (MAXIMUM)
$109.50Want a stronger trailing arm plus the performance advantage of the “Pull” bushing? We proudly give you the “DOGBONE”!
Same length (11-1/8″ C to C) and weight of a stock trailing arm but much stronger. Has “Pull” bushings installed, sized for 1/2″ bolts and is a bolt in ready unit.
(Sold Individually)Add to cartQuick View -
Add to cartQuick ViewRear End Brace Kit – 60″
$119.94This kit is design to reinforce the rear end so that the tubes do not bend if a wheel gets wrecked.
It will also prevent the rear end from deflecting under load and changing the alignment of the rear end while braking and under gas.(USRA Legal)
Add to cartQuick View -
Add to cartQuick ViewRear End Brace Kit (Main Bracket Only)
$18.98This is the main bracket for the “Rear End Brace Kits” (sold individually)
Add to cartQuick View -
Add to cartQuick ViewAxles, Non-Floater 30″, 5×5, (28 or 31 Spline)
$325.00These new Superior 28 or 31-spline axles feature screw in studs in a 5×5 wheel bolt pattern, , ¼ thick heavy duty bearing retainer plates, and tapered wheel bearings pressed on.
Add to cartQuick View -
Add to cartQuick ViewWasher, Axle
$5.60Stop spending big money on rubber seals and sleeves to stop rear end grease from being pulled into the RH rear end tube. Sold as pair.
Add to cartQuick View -
Add to cartQuick ViewBracket, Caliper (Small GM)
$12.50These caliper mount brackets are built to fit the small GM metric calipers. Use this kit to build your own custom rear end.
(Sold Individually)Add to cartQuick View
