ROTOR – PROLITE VENTED (11.75 X .810)
$47.99
- Description
Description
Cast from premium grade, long grain carbon iron which exhibits long wear, high thermal stability, and excellent resistance to distortion
32 vane design provides superior heat management and long service life
The straight vane design allows the same rotor to be used on both left or right hand sides
8 on 7″ mounting bolt circle is commonly used on brake hats and Grand National hubs
Sold individually
Related Products
-
Add to cartQuick ViewAxles, Non-Floater 30″, 5×5, (28 or 31 Spline)
$325.00These new Superior 28 or 31-spline axles feature screw in studs in a 5×5 wheel bolt pattern, , ¼ thick heavy duty bearing retainer plates, and tapered wheel bearings pressed on.
Add to cartQuick View -
Add to cartQuick ViewBracket, Caliper (Small GM)
$12.50These caliper mount brackets are built to fit the small GM metric calipers. Use this kit to build your own custom rear end.
(Sold Individually)Add to cartQuick View -
Add to cartQuick ViewTrailing Arm, Upper – OEM Reproduction w/ “Pull” Bushing
$132.50For those of you that want the benefits of the “Pull” bushing but without the hassle of installing them.
OEM reproduction stampings with our bushings installed. Sized for use with a 1/2″ bolt. These are a bolt in ready unit.
(Sold Individually)
Add to cartQuick View -
Add to cartQuick ViewQuick Change Mount, Upper Trailing Arm – w/ “PULL” Bushings – Metric (MAXIMUM)
$125.50This bolt on upper trailing arm mount is designed to allow use of a quick change into a stock GM metric chassis. Built with corrected pinion angle and our proven “Pull” Bushings.
NOTE: If installing on a Frankland quick change, the bracket will need to be modified and reinforced to fit.
Add to cartQuick View -
Add to cartQuick ViewHousing, Rear End – 60″ GN (L3) w/ Sport Mod Jigged
$901.3860″ offset new reproduction stamping Ford 9″ housing with new 3″ tubes and GN hub type snouts. Housings have fill and drain plug installed. SportMod jigged.
Spring Perchs & Brake Caliper Brackets are now Bolt-On Accessories (not included in Rear End Housing Price)
(IMCA Legal)
Custom Part is Non-Returnable and Non-Refundable.
Add to cartQuick View -
Add to cartQuick ViewTrailing Arm, Upper – BAREBONE (MAXIMUM)
$65.00Want a stronger trailing arm at a better price? We proudly give you the “BAREBONE”!
Same length and weight of a stock trailing arm but much stronger. Will accept any OEM type bushing.
(Sold Individually)
Add to cartQuick View -
Add to cartQuick ViewMount, Upper Trailing Arm – Kit (Ford 9″)
$103.00This kit includes two “Pull” bushings, two steel spools, a rectangular mount tube and side gusset bracket. Use this kit to build your own custom rear end.
Add to cartQuick View -
Add to cartQuick ViewCup, Spring – Tapered
$13.38These tapered profile spring cups are manufactured from high strength steel and are designed to minimize any stretch and bending while still being lightweight. Has a 1/4″ hole on bottom to allow bolting to your weight jack bolt.
Add to cartQuick View -
Add to cartQuick ViewBrackets, Trailing Arm (Single Hole)
$50.40Designed for the Wissota street stocks, these trailing arm brackets have the lowest mounting hole position possible. 4.0″ from axle tube to center of hole.
(Sold as a Pair)
Add to cartQuick View -
Add to cartQuick ViewAssembly, Rear End Housing – 60″ GN (L3) w/ Sport Mod Jigged
$1,538.4660″ offset new reproduction stamping Ford 9″ housing with new 3″ tubes and GN hub type snouts. Housings have fill and drain plug installed. Kit includes standard 5×5 GN hubs, hub bearings, seals, brake rotor, drive flange, 31 spline solid axles and all hardware necessary.
Spring Perchs & Brake Caliper Brackets are now Bolt-On Accessories (not included in Rear End Assembly Price)
Add to cartQuick View
