Quick Change Mount, Upper Trailing Arm – w/ “PULL” Bushings – Metric (MAXIMUM)
$125.50
This bolt on upper trailing arm mount is designed to allow use of a quick change into a stock GM metric chassis. Built with corrected pinion angle and our proven “Pull” Bushings.
NOTE: If installing on a Frankland quick change, the bracket will need to be modified and reinforced to fit.
- Description
- Additional information
Description
This bolt on upper trailing arm mount is designed to allow use of a quick change into a stock GM metric chassis. Built with corrected pinion angle and our proven “Pull” Bushings.
NOTE: If installing on a Frankland quick change, the bracket will need to be modified and reinforced to fit.
NOTE: The bolts need to be trimmed flush with the nut. This is normal and needed for clearance to get the mounts as low as possible for the best performance.
(Designed to have 5-7 degrees pinion angle at typical ride heights and wheelbase)
Additional information
| Weight | 6 lbs |
|---|
Related Products
-
Add to cartQuick ViewTrailing Arm, Upper – DOGBONE w/ “Pull” Bushing (MAXIMUM)
$109.50Want a stronger trailing arm plus the performance advantage of the “Pull” bushing? We proudly give you the “DOGBONE”!
Same length (11-1/8″ C to C) and weight of a stock trailing arm but much stronger. Has “Pull” bushings installed, sized for 1/2″ bolts and is a bolt in ready unit.
(Sold Individually)Add to cartQuick View -
Add to cartQuick ViewClamp, Limit Chain (1-1/2” Tube) – Wehrs
$25.001-1/2” Tube Diameter Clamp For Limit Chains on Chassis Side
Add to cartQuick View -
Add to cartQuick ViewRear End Brace Kit – 60″
$119.94This kit is design to reinforce the rear end so that the tubes do not bend if a wheel gets wrecked.
It will also prevent the rear end from deflecting under load and changing the alignment of the rear end while braking and under gas.(USRA Legal)
Add to cartQuick View -
Add to cartQuick ViewAxles, Non-Floater 30″, 5×5, (28 or 31 Spline)
$325.00These new Superior 28 or 31-spline axles feature screw in studs in a 5×5 wheel bolt pattern, , ¼ thick heavy duty bearing retainer plates, and tapered wheel bearings pressed on.
Add to cartQuick View -
Add to cartQuick ViewBolt, Weight Jack – 11″ Long
$21.991 diameter x 11 long weight jack bolt. (1″-8 Coarse Thread)
Add to cartQuick View -
Add to cartQuick View
Axles, Non-Floater 30″, 5×4 3/4, (31 Spline)
$325.00These new Currie 31-spline axles feature press in studs in a 5×4 3/4 wheel bolt pattern, , ¼ thick heavy duty bearing retainer plates, and tapered wheel bearings pressed on.
Add to cartQuick View -
Add to cartQuick ViewPerch, Spring Kit (Offset or Centered)
$31.98Strong, simple and lightweight spring perches that you can use to build your custom rear end. (sold as a pair)
Add to cartQuick View -
Add to cartQuick ViewBRACKET, CHASSIS PANHARD, BOLT ON – 3 INCH OFFSET (PAIR)
$50.00BRACKET, CHASSIS PANHARD, BOLT ON – 3 INCH OFFSET (PAIR)
Add to cartQuick View -
Add to cartQuick ViewBrackets, Trailing Arm – HEAVY, Slotted (LR ONLY)
$100.00Designed for stock cars with a 7.5″ max trailing arm length.
This trailing arm bracket use common offset slugs (sold separately) to allow you to change the amount of lead or trail in the rear end. Simply replace the slug with different combination of offset slugs. Tack weld the slugs to secure them to the trailing arm.
This bracket is also built heavy, weigh 7.5lbs (with slugs) to help increase LR rear end weight.
Perfect for the guys that already have or Extreme or Xtrmer Drop brackets. Simply replace the LR bracket and have increase drive and adjustability.
(Sold individually)
(Slugs sold separately)
Add to cartQuick View -
Add to cartQuick ViewBrackets, Trailing Arm (Extreme Drop)
$112.00Looking for increased forward bit and traction? Then this trailing arm bracket kit is a must have.
Specifically designed to increase LR drive off the corner and corner entry adjustability with multiple hole adjustments on the RR.
LR bracket is 6.75″ from axle tube to center of bottom hole. (USRA/IMCA Stock Car Legal)
(Sold as a Pair)
Add to cartQuick View
