SWINGARM – MOD (5/8″) – 16″ (MAXIMUM)
$65.00
Lower swingarm suspension link designed to give maximum forward drive!
- Description
Description
Lower swingarm suspension link designed to give maximum forward drive!
Precision 5/8″ rod end on BOTH ends.
16″ nominal length center to center.
Single hole plate with clearance for increased drop out angles.
Use on Midwest Modifieds and Late Models
You may also like…
-
Add to cartQuick ViewSWINGARM – MOD (5/8″) – 15″ (MAXIMUM)
$65.00Lower swingarm suspension link designed to give maximum forward drive!
Add to cartQuick View -
Add to cartQuick ViewSWINGARM – MOD (5/8″) – 13″ (MAXIMUM)
$65.00Lower swingarm suspension link designed to give maximum forward drive!
Add to cartQuick View
Related Products
-
Add to cartQuick ViewAxles, Non-Floater 30″, 5×5, (28 or 31 Spline)
$325.00These new Superior 28 or 31-spline axles feature screw in studs in a 5×5 wheel bolt pattern, , ¼ thick heavy duty bearing retainer plates, and tapered wheel bearings pressed on.
Add to cartQuick View -
Add to cartQuick ViewWasher, Axle
$5.60Stop spending big money on rubber seals and sleeves to stop rear end grease from being pulled into the RH rear end tube. Sold as pair.
Add to cartQuick View -
Add to cartQuick ViewClamp, Limit Chain (1-1/2” Tube) – Wehrs
$25.001-1/2” Tube Diameter Clamp For Limit Chains on Chassis Side
Add to cartQuick View -
Add to cartQuick ViewBrackets, Trailing Arm (Single Hole)
$50.40Designed for the Wissota street stocks, these trailing arm brackets have the lowest mounting hole position possible. 4.0″ from axle tube to center of hole.
(Sold as a Pair)
Add to cartQuick View -
Add to cartQuick ViewCup, Spring – Tapered
$13.38These tapered profile spring cups are manufactured from high strength steel and are designed to minimize any stretch and bending while still being lightweight. Has a 1/4″ hole on bottom to allow bolting to your weight jack bolt.
Add to cartQuick View -
Add to cartQuick ViewAssembly, Rear End Housing – 60″ GN (L3) w/ Sport Mod Jigged
$1,538.4660″ offset new reproduction stamping Ford 9″ housing with new 3″ tubes and GN hub type snouts. Housings have fill and drain plug installed. Kit includes standard 5×5 GN hubs, hub bearings, seals, brake rotor, drive flange, 31 spline solid axles and all hardware necessary.
Spring Perchs & Brake Caliper Brackets are now Bolt-On Accessories (not included in Rear End Assembly Price)
Add to cartQuick View -
Add to cartQuick ViewRear End Brace Kit (Main Bracket Only)
$18.98This is the main bracket for the “Rear End Brace Kits” (sold individually)
Add to cartQuick View -
Add to cartQuick ViewRear End Brace Kit – 60″
$119.94This kit is design to reinforce the rear end so that the tubes do not bend if a wheel gets wrecked.
It will also prevent the rear end from deflecting under load and changing the alignment of the rear end while braking and under gas.(USRA Legal)
Add to cartQuick View -
Add to cartQuick ViewBracket, Caliper (Small GM)
$12.50These caliper mount brackets are built to fit the small GM metric calipers. Use this kit to build your own custom rear end.
(Sold Individually)Add to cartQuick View -
Add to cartQuick ViewQuick Change Mount, Upper Trailing Arm – w/ “PULL” Bushings – Metric (MAXIMUM)
$125.50This bolt on upper trailing arm mount is designed to allow use of a quick change into a stock GM metric chassis. Built with corrected pinion angle and our proven “Pull” Bushings.
NOTE: If installing on a Frankland quick change, the bracket will need to be modified and reinforced to fit.
Add to cartQuick View
