SWINGARM – MOD (5/8″) – 13″ (MAXIMUM)
$65.00
Lower swingarm suspension link designed to give maximum forward drive!
- Description
Description
Lower swingarm suspension link designed to give maximum forward drive!
Precision 5/8″ rod end on BOTH ends.
13″ nominal length center to center.
Single hole plate with clearance for increased drop out angles.
Use on Modifieds and Late Models.
You may also like…
-
Add to cartQuick ViewSWINGARM – MOD (5/8″) – 15″ (MAXIMUM)
$65.00Lower swingarm suspension link designed to give maximum forward drive!
Add to cartQuick View -
Add to cartQuick View
SWINGARM – MOD (5/8″) – 16″ (MAXIMUM)
$65.00Lower swingarm suspension link designed to give maximum forward drive!
Add to cartQuick View
Related Products
-
Add to cartQuick ViewBrackets, Trailing Arm (Hobby Stock)
$50.40Designed for the Hobby stocks, these trailing arm brackets have the lowest mounting hole position possible. 2.50″ from axle tube to center of hole.
(Sold as a Pair)
Add to cartQuick View -
Add to cartQuick ViewCup, Spring – Tapered
$13.38These tapered profile spring cups are manufactured from high strength steel and are designed to minimize any stretch and bending while still being lightweight. Has a 1/4″ hole on bottom to allow bolting to your weight jack bolt.
Add to cartQuick View -
Add to cartQuick ViewBolt, Weight Jack – 11″ Long
$21.991 diameter x 11 long weight jack bolt. (1″-8 Coarse Thread)
Add to cartQuick View -
Add to cartQuick ViewTrailing Arm, Upper – OEM Reproduction w/ “Pull” Bushing
$132.50For those of you that want the benefits of the “Pull” bushing but without the hassle of installing them.
OEM reproduction stampings with our bushings installed. Sized for use with a 1/2″ bolt. These are a bolt in ready unit.
(Sold Individually)
Add to cartQuick View -
Add to cartQuick ViewBrackets, Trailing Arm (Extreme Drop)
$112.00Looking for increased forward bit and traction? Then this trailing arm bracket kit is a must have.
Specifically designed to increase LR drive off the corner and corner entry adjustability with multiple hole adjustments on the RR.
LR bracket is 6.75″ from axle tube to center of bottom hole. (USRA/IMCA Stock Car Legal)
(Sold as a Pair)
Add to cartQuick View -
Add to cartQuick ViewAxle, 32″ GN Gun Drilled (31 Spline)
$199.5029.5″ Premium GN gun drilled axle.
Add to cartQuick View -
Add to cartQuick ViewTrailing Arm, Lower – BAREBONE (MAXIMUM)
$53.60Want a stronger trailing arm at a better price? We proudly give you the “BAREBONE”!
Same length and weight of a stock trailing arm but much stronger. Will accept any OEM type bushing.
(Sold Individually)
Add to cartQuick View -
Add to cartQuick ViewBrackets, Trailing Arm (Single Hole)
$50.40Designed for the Wissota street stocks, these trailing arm brackets have the lowest mounting hole position possible. 4.0″ from axle tube to center of hole.
(Sold as a Pair)
Add to cartQuick View -
Add to cartQuick ViewWasher, Axle
$5.60Stop spending big money on rubber seals and sleeves to stop rear end grease from being pulled into the RH rear end tube. Sold as pair.
Add to cartQuick View -
Add to cartQuick View
Axle, 29.5″ GN Gun Drilled (31 Spline)
$199.5029.5″ Premium GN gun drilled axle.
Add to cartQuick View
