Medieval Quick Change Upper Trailing Arm Mount w/ “Spherical” Bushings – Metric
$117.00
This bolt on upper trailing arm mount is designed to allow use of a quick change into a stock GM metric chassis. Built with corrected pinion angle and our proven “Spherical” Bushings.
- Description
- Additional information
- Reviews (0)
Description
This bolt on upper trailing arm mount is designed to allow use of a quick change into a stock GM metric chassis. Built with corrected pinion angle and our proven “Spherical” Bushings.
Additional information
| Weight | 8 lbs |
|---|
Be the first to review “Medieval Quick Change Upper Trailing Arm Mount w/ “Spherical” Bushings – Metric”
Related Products
-
Add to cartQuick ViewMedieval “Pull” Upper Trailing Arm
$90.00For those of you that want the benefits of the “Pull” bushing but without the hassle of installing them.
OEM reproduction stampings with our bushings installed. Sized for use with a 1/2″ bolt. These are a bolt in ready unit.
(Sold Individually)
Add to cartQuick View -
Add to cartQuick ViewHousing, Rear End – 60″ GN (Offset) – Full Stock Car Extreme Drop Jigged
$695.0060″ offset new reproduction stamping Ford 9″ housing with new 3″ tubes and GN hub type snouts. Housings have fill and drain plug installed.
Jigged with our:
– “Extreme drop” trailing arm brackets
– “Pull” upper bushings mounts
– Brake caliper mounts (GM Metric)Spring perches and shock mounts come as kits so that you can properly locate them for your specific chassis. USRA/IMCA legal.
Custom Part is Non-Returnable and Non-Refundable.
Add to cartQuick View -
Add to cartQuick ViewHousing, Rear End – 60″ Non Floater IMCA Hobby Stock Jigged
$655.00New reproduction stamping Ford 9″ housing with new 3″ tubes and big bearing type flanges.
Jigged with our:
– Lower trailing arm mounts
– Upper “Pull” bushing mounts
– Spring perches
– Shock mounts(IMCA Approved)
Custom Part is Non-Returnable and Non-Refundable.
Add to cartQuick View -
Add to cartQuick ViewBolt, Weight Jack 11
$17.991 diameter x 11 long weight jack bolt.
Add to cartQuick View -
Add to cartQuick ViewRear End Brace Kit – 60″
$99.95This kit is design to reinforce the rear end so that the tubes do not bend if a wheel gets wrecked.
It will also prevent the rear end from deflecting under load and changing the alignment of the rear end while braking and under gas.(USRA Legal)
Add to cartQuick View -
Add to cartQuick ViewMount, Upper Trailing Arm
$75.00This kit includes two “Pull” bushings, two steel spools, a rectangular mount tube and side gusset bracket. Use this kit to build your own custom rear end.
Add to cartQuick View -
Add to cartQuick ViewAxles, Non-Floater 30″, 5×4 3/4, 31 spline
$225.00These new Currie 31-spline axles feature press in studs in a 5×4 3/4 wheel bolt pattern, , ¼ thick heavy duty bearing retainer plates, and tapered wheel bearings pressed on.
Add to cartQuick View -
Add to cartQuick ViewSpherical Bearing – Rear Trailing Arms
$25.99Recommend using these bearings on the rear end mounts only. (if rules allow) They will take all of the bind out of the rear end. Couple these with using our Medieval “Pull” Bushings (MMX FB397) on the upper trailing arms – this will give you the best configuration possible.
Sold individually
Add to cartQuick View -
Add to cartQuick ViewBrackets, Trailing Arm (Extreme Drop LR)
$100.00Looking for increased forward bit and traction? Then this trailing arm bracket kit is a must have.
Specifically designed to increase LR drive off the corner and corner entry adjustability with multiple hole adjustments on the RR.
LR bracket is 6.75″ from axle tube to center of bottom hole. (USRA/IMCA Stock Car Legal)
(Sold as a Pair)
Add to cartQuick View -
Add to cartQuick ViewPerch, Spring (Centered)
$15.00Strong, simple and lightweight spring perches that you can use to build your custom rear end.
Add to cartQuick View
Reviews
There are no reviews yet.