Clamp, Limit Chain (1-3/4” Tube) – Wehrs
$25.00
1-3/4” Tube Diameter Clamp For Limit Chains on Chassis Side
You may also like…
-
Add to cartQuick ViewBolt On, Clamp-3″ Chain Limiter w/ Chain and Adjuster Kit
$107.46Bolt On, Clamp-3″ Chain Limiter w/ Chain and Adjuster Kit
Add to cartQuick View -
Select optionsQuick ViewBolt On, Clamp-3″ (Chain Limiter) MAXIMUM
$33.60 – $41.44Bolt On, Clamp-3″ (Chain Limiter)
Select optionsQuick View
Related Products
-
Add to cartQuick ViewClamp, Limit Chain (1-1/2” Tube) – Wehrs
$25.001-1/2” Tube Diameter Clamp For Limit Chains on Chassis Side
Add to cartQuick View -
Add to cartQuick ViewBrackets, Trailing Arm (Single Hole)
$50.40Designed for the Wissota street stocks, these trailing arm brackets have the lowest mounting hole position possible. 4.0″ from axle tube to center of hole.
(Sold as a Pair)
Add to cartQuick View -
Add to cartQuick ViewAxle, 29.5″ GN Gun Drilled (31 Spline)
$199.5029.5″ Premium GN gun drilled axle.
Add to cartQuick View -
Add to cartQuick ViewBrackets, Trailing Arm (Extreme Drop)
$112.00Looking for increased forward bit and traction? Then this trailing arm bracket kit is a must have.
Specifically designed to increase LR drive off the corner and corner entry adjustability with multiple hole adjustments on the RR.
LR bracket is 6.75″ from axle tube to center of bottom hole. (USRA/IMCA Stock Car Legal)
(Sold as a Pair)
Add to cartQuick View -
Add to cartQuick ViewCup, Spring – Tapered
$13.38These tapered profile spring cups are manufactured from high strength steel and are designed to minimize any stretch and bending while still being lightweight. Has a 1/4″ hole on bottom to allow bolting to your weight jack bolt.
Add to cartQuick View -
Add to cartQuick ViewAxles, Non-Floater 30″, 5×5, (28 or 31 Spline)
$325.00These new Superior 28 or 31-spline axles feature screw in studs in a 5×5 wheel bolt pattern, , ¼ thick heavy duty bearing retainer plates, and tapered wheel bearings pressed on.
Add to cartQuick View -
Add to cartQuick ViewBrackets, Trailing Arm (Multi-Hole)
$84.00This trailing arm bracket kit was designed to allow trailing arm angle adjustments just like what can be done on modifieds…..
(Sold as a Pair)
Add to cartQuick View -
Add to cartQuick ViewRear End Brace Kit – 60″
$119.94This kit is design to reinforce the rear end so that the tubes do not bend if a wheel gets wrecked.
It will also prevent the rear end from deflecting under load and changing the alignment of the rear end while braking and under gas.(USRA Legal)
Add to cartQuick View -
Add to cartQuick ViewBrackets, Trailing Arm – HEAVY, Slotted (LR ONLY)
$100.00Designed for stock cars with a 7.5″ max trailing arm length.
This trailing arm bracket use common offset slugs (sold separately) to allow you to change the amount of lead or trail in the rear end. Simply replace the slug with different combination of offset slugs. Tack weld the slugs to secure them to the trailing arm.
This bracket is also built heavy, weigh 7.5lbs (with slugs) to help increase LR rear end weight.
Perfect for the guys that already have or Extreme or Xtrmer Drop brackets. Simply replace the LR bracket and have increase drive and adjustability.
(Sold individually)
(Slugs sold separately)
Add to cartQuick View -
Add to cartQuick ViewRear End Brace Kit (Main Bracket Only)
$18.98This is the main bracket for the “Rear End Brace Kits” (sold individually)
Add to cartQuick View
