Spacer, 5/8″ High Misalignment – 1″ Long
$8.75
5/8″ heim 1/2″ bolt high misalignment spacer 1″ long. Measured from the end of the spacer to the heim.
- Measurement is not total overall length
- Description
Description
5/8″ heim 1/2″ bolt high misalignment spacer 1″ long. Measured from the end of the spacer to the heim.
- Measurement is not total overall length
Related Products
-
Add to cartQuick ViewAxles, Non-Floater 30″, 5×5, (28 or 31 Spline)
$325.00These new Superior 28 or 31-spline axles feature screw in studs in a 5×5 wheel bolt pattern, , ¼ thick heavy duty bearing retainer plates, and tapered wheel bearings pressed on.
Add to cartQuick View -
Add to cartQuick ViewBushing, “SPHERICAL” – Trailing Arm (MAXIMUM)
$44.95MAXIMUM Spherical Bushing
Sold individually
Add to cartQuick View -
Add to cartQuick View
Axles, Non-Floater 30″, 5×4 3/4, (31 Spline)
$325.00These new Currie 31-spline axles feature press in studs in a 5×4 3/4 wheel bolt pattern, , ¼ thick heavy duty bearing retainer plates, and tapered wheel bearings pressed on.
Add to cartQuick View -
Add to cartQuick ViewBushing, “PULL” (Trailing Arms)
$35.75This is a new bushing that is used in the upper & lower trailing arms to create side bite and cushioning of the rear end.
Sold individually
Add to cartQuick View -
Add to cartQuick ViewClamp, Limit Chain (1-1/2” Tube) – Wehrs
$25.001-1/2” Tube Diameter Clamp For Limit Chains on Chassis Side
Add to cartQuick View -
Add to cartQuick ViewQuick Change Mount, Upper Trailing Arm – w/ “SPHERICAL” Bushings – Metric (MAXIMUM)
$166.99This bolt on upper trailing arm mount is designed to allow use of a quick change into a stock GM metric chassis. Built with corrected pinion angle and our proven “Spherical” Bushings.
NOTE: If installing on a Frankland quick change, the bracket will need to be modified and reinforced to fit.
Add to cartQuick View -
Add to cartQuick ViewBRACKET, CHASSIS PANHARD, BOLT ON – 3 INCH OFFSET (PAIR)
$50.00BRACKET, CHASSIS PANHARD, BOLT ON – 3 INCH OFFSET (PAIR)
Add to cartQuick View -
Add to cartQuick ViewAssembly, Rear End Housing – 60″ GN (L3) w/ Sport Mod Jigged
$1,538.4660″ offset new reproduction stamping Ford 9″ housing with new 3″ tubes and GN hub type snouts. Housings have fill and drain plug installed. Kit includes standard 5×5 GN hubs, hub bearings, seals, brake rotor, drive flange, 31 spline solid axles and all hardware necessary.
Spring Perchs & Brake Caliper Brackets are now Bolt-On Accessories (not included in Rear End Assembly Price)
Add to cartQuick View -
Add to cartQuick ViewTrailing Arm, Upper – OEM Reproduction w/ “Pull” Bushing
$132.50For those of you that want the benefits of the “Pull” bushing but without the hassle of installing them.
OEM reproduction stampings with our bushings installed. Sized for use with a 1/2″ bolt. These are a bolt in ready unit.
(Sold Individually)
Add to cartQuick View -
Add to cartQuick ViewWasher, Axle
$5.60Stop spending big money on rubber seals and sleeves to stop rear end grease from being pulled into the RH rear end tube. Sold as pair.
Add to cartQuick View
