Mount, Pinion Panhard QC (Right Side Climber, Steel)
$130.00
MAXIMUM Performance right side climbing panhard mount for quick change rear ends. (Steel)
Mounts J-Bar to QC rear end – 4 3/8″ offset from pinion.
- Description
Description
MAXIMUM Performance right side climbing panhard mount for quick change rear ends. (Steel)
Mounts J-Bar to QC rear end – 4 3/8″ offset from pinion.
Lightest weight pinion mount in the industry.
Laser cut out of high strength Grade 50 steel for strength and durability.
Kit includes climbing gear and hardware needed for J-bar.
You may also like…
-
Add to cartQuick ViewMount, Pinion Panhard 9″ Ford (Right Side Climber, Steel)
$130.00MAXIMUM Performance right side climbing panhard mount for Ford 9″ rear ends. (Steel)
Mounts J-Bar to 9″ third-member – 4 3/8″ offset from pinion.
Add to cartQuick View
Related Products
-
Add to cartQuick ViewTrailing Arm, Upper – OEM Reproduction w/ “Pull” Bushing
$132.50For those of you that want the benefits of the “Pull” bushing but without the hassle of installing them.
OEM reproduction stampings with our bushings installed. Sized for use with a 1/2″ bolt. These are a bolt in ready unit.
(Sold Individually)
Add to cartQuick View -
Add to cartQuick ViewBrackets, Trailing Arm (Extreme Drop)
$112.00Looking for increased forward bit and traction? Then this trailing arm bracket kit is a must have.
Specifically designed to increase LR drive off the corner and corner entry adjustability with multiple hole adjustments on the RR.
LR bracket is 6.75″ from axle tube to center of bottom hole. (USRA/IMCA Stock Car Legal)
(Sold as a Pair)
Add to cartQuick View -
Add to cartQuick ViewWasher, Axle
$5.60Stop spending big money on rubber seals and sleeves to stop rear end grease from being pulled into the RH rear end tube. Sold as pair.
Add to cartQuick View -
Add to cartQuick ViewBracket, Caliper (Small GM)
$12.50These caliper mount brackets are built to fit the small GM metric calipers. Use this kit to build your own custom rear end.
(Sold Individually)Add to cartQuick View -
Add to cartQuick ViewBrackets, Trailing Arm (Single Hole)
$50.40Designed for the Wissota street stocks, these trailing arm brackets have the lowest mounting hole position possible. 4.0″ from axle tube to center of hole.
(Sold as a Pair)
Add to cartQuick View -
Add to cartQuick ViewQuick Change Mount, Upper Trailing Arm – w/ “SPHERICAL” Bushings – Metric (MAXIMUM)
$166.99This bolt on upper trailing arm mount is designed to allow use of a quick change into a stock GM metric chassis. Built with corrected pinion angle and our proven “Spherical” Bushings.
NOTE: If installing on a Frankland quick change, the bracket will need to be modified and reinforced to fit.
Add to cartQuick View -
Add to cartQuick ViewAxles, Non-Floater 30″, 5×5, (28 or 31 Spline)
$325.00These new Superior 28 or 31-spline axles feature screw in studs in a 5×5 wheel bolt pattern, , ¼ thick heavy duty bearing retainer plates, and tapered wheel bearings pressed on.
Add to cartQuick View -
Add to cartQuick ViewRear End Brace Kit (Main Bracket Only)
$18.98This is the main bracket for the “Rear End Brace Kits” (sold individually)
Add to cartQuick View -
Add to cartQuick ViewBolt, Weight Jack – 11″ Long
$21.991 diameter x 11 long weight jack bolt. (1″-8 Coarse Thread)
Add to cartQuick View -
Add to cartQuick View
Axles, Non-Floater 30″, 5×4 3/4, (31 Spline)
$325.00These new Currie 31-spline axles feature press in studs in a 5×4 3/4 wheel bolt pattern, , ¼ thick heavy duty bearing retainer plates, and tapered wheel bearings pressed on.
Add to cartQuick View
