Bolt On, Caliper Bracket (Small GM) – HEAVY LR (MAXIMUM)
$75.00
Bolt On, Caliper Bracket (Small GM)
- Description
Description
Extra Heavy for LR weight split caliper bracket to allow installing without removing hubs onto 3” axle tube. Has dual gussets for rigidity so that you do not have caliper deflection and piston push back. 5.5” between mounting holes.
**Weighs 4.5lbs**
**Caliper bracket MUST be welded to rear end housing to keep from rotating**
**SOLD INDIVIDUALLY**
You may also like…
-
Add to cartQuick ViewBolt On, Trailing Arm Bracket Kit – Multi Hole (MAXIMUM)
$146.66Bolt On, Trailing Arm Bracket Kit Multi Hole
Add to cartQuick View -
Select optionsQuick ViewQuick Change Rear End – Assembly
$2,828.86Quick Change Rear End Assembly 10″ Alum Spool and Steel Tubes
Select optionsQuick View -
Add to cartQuick ViewBolt On, Spring Perch – Offset (MAXIMUM)
$45.86Bolt On, Spring Perch Offset
Add to cartQuick View -
Add to cartQuick ViewBolt On, Spring Perch – Center (MAXIMUM)
$45.86Bolt On, Spring Perch Center
Add to cartQuick View -
Select optionsQuick ViewQuick Change Rear End – Bare
$2,129.24Quick Change Rear End With 486 R&P 10″ Alum Spool and Steel Tubes.
Select optionsQuick View -
Add to cartQuick ViewQuick Change Mount, Upper Trailing Arm – w/ “PULL” Bushings – Metric (MAXIMUM)
$121.50This bolt on upper trailing arm mount is designed to allow use of a quick change into a stock GM metric chassis. Built with corrected pinion angle and our proven “Pull” Bushings.
NOTE: If installing on a Frankland quick change, the bracket will need to be modified and reinforced to fit.
Add to cartQuick View
Related Products
-
Add to cartQuick ViewQuick Change Mount, Upper Trailing Arm – w/ “SPHERICAL” Bushings – Metric (MAXIMUM)
$166.99This bolt on upper trailing arm mount is designed to allow use of a quick change into a stock GM metric chassis. Built with corrected pinion angle and our proven “Spherical” Bushings.
NOTE: If installing on a Frankland quick change, the bracket will need to be modified and reinforced to fit.
Add to cartQuick View -
Add to cartQuick ViewAxles, Non-Floater 30″, 5×5, (28 or 31 Spline)
$325.00These new Superior 28 or 31-spline axles feature screw in studs in a 5×5 wheel bolt pattern, , ¼ thick heavy duty bearing retainer plates, and tapered wheel bearings pressed on.
Add to cartQuick View -
Add to cartQuick ViewBushing, “PULL” (Trailing Arms)
$30.75This is a new bushing that is used in the upper & lower trailing arms to create side bite and cushioning of the rear end.
Sold individually
Add to cartQuick View -
Add to cartQuick ViewCup, Spring – Tapered
$13.38These tapered profile spring cups are manufactured from high strength steel and are designed to minimize any stretch and bending while still being lightweight. Has a 1/4″ hole on bottom to allow bolting to your weight jack bolt.
Add to cartQuick View -
Add to cartQuick View
Axles, Non-Floater 30″, 5×4 3/4, (31 Spline)
$325.00These new Currie 31-spline axles feature press in studs in a 5×4 3/4 wheel bolt pattern, , ¼ thick heavy duty bearing retainer plates, and tapered wheel bearings pressed on.
Add to cartQuick View -
Add to cartQuick ViewAxle, 29.5″ GN Gun Drilled (31 Spline)
$199.5029.5″ Premium GN gun drilled axle.
Add to cartQuick View -
Add to cartQuick ViewBolt On, Trailing Arm Bracket Kit – HEAVY, Single Hole LR ONLY (MAXIMUM)
$156.00Bolt On, Trailing Arm Bracket Kit – HEAVY, Single Hole (LR Only)
Add to cartQuick View -
Add to cartQuick View
Axle, 32″ GN Gun Drilled (31 Spline)
$199.5029.5″ Premium GN gun drilled axle.
Add to cartQuick View -
Add to cartQuick ViewBrackets, Trailing Arm (Hobby Stock)
$50.40Designed for the Hobby stocks, these trailing arm brackets have the lowest mounting hole position possible. 2.50″ from axle tube to center of hole.
(Sold as a Pair)
Add to cartQuick View -
Add to cartQuick ViewWasher, Axle
$5.60Stop spending big money on rubber seals and sleeves to stop rear end grease from being pulled into the RH rear end tube. Sold as pair.
Add to cartQuick View
