Quick Change Mount, Upper Trailing Arm – NO Bushings – Metric (MAXIMUM)
$105.80
This bolt on upper trailing arm mount is designed to allow use of a quick change into a stock GM metric chassis. Built with corrected pinion angle. NO Bushings included.
NOTE: If installing on a Frankland quick change, the bracket will need to be modified and reinforced to fit.
- Description
- Additional information
Description
This bolt on upper trailing arm mount is designed to allow use of a quick change into a stock GM metric chassis. Built with corrected pinion angle. NO Bushings included.
NOTE: If installing on a Frankland quick change, the bracket will need to be modified and reinforced to fit.
(Designed to have 5-7 degrees pinion angle at typical ride heights and wheelbase)
Additional information
| Weight | 6 lbs |
|---|
You may also like…
-
Add to cartQuick ViewQuick Change Mount, Upper Trailing Arm – w/ “PULL” Bushings – Metric (MAXIMUM)
$125.50This bolt on upper trailing arm mount is designed to allow use of a quick change into a stock GM metric chassis. Built with corrected pinion angle and our proven “Pull” Bushings.
NOTE: If installing on a Frankland quick change, the bracket will need to be modified and reinforced to fit.
Add to cartQuick View -
Add to cartQuick ViewQuick Change Mount, Upper Trailing Arm – w/ “SPHERICAL” Bushings – Metric (MAXIMUM)
$166.99This bolt on upper trailing arm mount is designed to allow use of a quick change into a stock GM metric chassis. Built with corrected pinion angle and our proven “Spherical” Bushings.
NOTE: If installing on a Frankland quick change, the bracket will need to be modified and reinforced to fit.
Add to cartQuick View
Related Products
-
Add to cartQuick ViewBrackets, Trailing Arm (Single Hole)
$50.40Designed for the Wissota street stocks, these trailing arm brackets have the lowest mounting hole position possible. 4.0″ from axle tube to center of hole.
(Sold as a Pair)
Add to cartQuick View -
Add to cartQuick ViewBrackets, Trailing Arm (Hobby Stock)
$50.40Designed for the Hobby stocks, these trailing arm brackets have the lowest mounting hole position possible. 2.50″ from axle tube to center of hole.
(Sold as a Pair)
Add to cartQuick View -
Add to cartQuick ViewBrackets, Trailing Arm (Extreme Drop)
$112.00Looking for increased forward bit and traction? Then this trailing arm bracket kit is a must have.
Specifically designed to increase LR drive off the corner and corner entry adjustability with multiple hole adjustments on the RR.
LR bracket is 6.75″ from axle tube to center of bottom hole. (USRA/IMCA Stock Car Legal)
(Sold as a Pair)
Add to cartQuick View -
Add to cartQuick ViewPerch, Spring Kit (Offset or Centered)
$31.98Strong, simple and lightweight spring perches that you can use to build your custom rear end. (sold as a pair)
Add to cartQuick View -
Add to cartQuick ViewAssembly, Rear End Housing – 60″ GN (L3) w/ Sport Mod Jigged
$1,538.4660″ offset new reproduction stamping Ford 9″ housing with new 3″ tubes and GN hub type snouts. Housings have fill and drain plug installed. Kit includes standard 5×5 GN hubs, hub bearings, seals, brake rotor, drive flange, 31 spline solid axles and all hardware necessary.
Spring Perchs & Brake Caliper Brackets are now Bolt-On Accessories (not included in Rear End Assembly Price)
Add to cartQuick View -
Add to cartQuick ViewRear End Brace Kit – 60″
$119.94This kit is design to reinforce the rear end so that the tubes do not bend if a wheel gets wrecked.
It will also prevent the rear end from deflecting under load and changing the alignment of the rear end while braking and under gas.(USRA Legal)
Add to cartQuick View -
Add to cartQuick ViewBRACKET, CHASSIS PANHARD, BOLT ON – 3 INCH OFFSET (PAIR)
$50.00BRACKET, CHASSIS PANHARD, BOLT ON – 3 INCH OFFSET (PAIR)
Add to cartQuick View -
Add to cartQuick ViewBracket, Caliper (Small GM)
$12.50These caliper mount brackets are built to fit the small GM metric calipers. Use this kit to build your own custom rear end.
(Sold Individually)Add to cartQuick View -
Add to cartQuick View
Quick Change Mount, Upper Trailing Arm – w/ “PULL” Bushings – Metric (MAXIMUM)
$125.50This bolt on upper trailing arm mount is designed to allow use of a quick change into a stock GM metric chassis. Built with corrected pinion angle and our proven “Pull” Bushings.
NOTE: If installing on a Frankland quick change, the bracket will need to be modified and reinforced to fit.
Add to cartQuick View -
Add to cartQuick ViewAxle, 29.5″ GN Gun Drilled (31 Spline)
$199.5029.5″ Premium GN gun drilled axle.
Add to cartQuick View
