Clamp, Limit Chain (1-1/2” Tube) – Wehrs
$25.00
1-1/2” Tube Diameter Clamp For Limit Chains on Chassis Side
You may also like…
-
Select optionsQuick ViewBolt On, Clamp-3″ (Chain Limiter) MAXIMUM
$33.60 – $41.44Bolt On, Clamp-3″ (Chain Limiter)
Select optionsQuick View -
Add to cartQuick ViewBolt On, Clamp-3″ Chain Limiter w/ Chain and Adjuster Kit
$107.46Bolt On, Clamp-3″ Chain Limiter w/ Chain and Adjuster Kit
Add to cartQuick View
Related Products
-
Add to cartQuick ViewAxles, Non-Floater 30″, 5×5, (28 or 31 Spline)
$325.00These new Superior 28 or 31-spline axles feature screw in studs in a 5×5 wheel bolt pattern, , ¼ thick heavy duty bearing retainer plates, and tapered wheel bearings pressed on.
Add to cartQuick View -
Add to cartQuick ViewBrackets, Trailing Arm (Multi-Hole)
$84.00This trailing arm bracket kit was designed to allow trailing arm angle adjustments just like what can be done on modifieds…..
(Sold as a Pair)
Add to cartQuick View -
Add to cartQuick ViewAssembly, Rear End Housing – 60″ GN (L3) w/ Sport Mod Jigged
$1,538.4660″ offset new reproduction stamping Ford 9″ housing with new 3″ tubes and GN hub type snouts. Housings have fill and drain plug installed. Kit includes standard 5×5 GN hubs, hub bearings, seals, brake rotor, drive flange, 31 spline solid axles and all hardware necessary.
Spring Perchs & Brake Caliper Brackets are now Bolt-On Accessories (not included in Rear End Assembly Price)
Add to cartQuick View -
Add to cartQuick ViewTrailing Arm, Upper – OEM Reproduction w/ “Pull” Bushing
$132.50For those of you that want the benefits of the “Pull” bushing but without the hassle of installing them.
OEM reproduction stampings with our bushings installed. Sized for use with a 1/2″ bolt. These are a bolt in ready unit.
(Sold Individually)
Add to cartQuick View -
Add to cartQuick ViewWasher, Axle
$5.60Stop spending big money on rubber seals and sleeves to stop rear end grease from being pulled into the RH rear end tube. Sold as pair.
Add to cartQuick View -
Add to cartQuick ViewBRACKET, CHASSIS PANHARD, BOLT ON – 3 INCH OFFSET (PAIR)
$50.00BRACKET, CHASSIS PANHARD, BOLT ON – 3 INCH OFFSET (PAIR)
Add to cartQuick View -
Add to cartQuick ViewBrackets, Trailing Arm (Extreme Drop)
$112.00Looking for increased forward bit and traction? Then this trailing arm bracket kit is a must have.
Specifically designed to increase LR drive off the corner and corner entry adjustability with multiple hole adjustments on the RR.
LR bracket is 6.75″ from axle tube to center of bottom hole. (USRA/IMCA Stock Car Legal)
(Sold as a Pair)
Add to cartQuick View -
Add to cartQuick ViewBolt On, Trailing Arm Bracket Kit – HEAVY, Single Hole LR ONLY (MAXIMUM)
$156.00Bolt On, Trailing Arm Bracket Kit – HEAVY, Single Hole (LR Only)
Add to cartQuick View -
Add to cartQuick ViewAxle, 29.5″ GN Solid (31 Spline)
$109.9929.5″ Premium GN axle.
Add to cartQuick View -
Add to cartQuick ViewBrackets, Trailing Arm (Single Hole)
$50.40Designed for the Wissota street stocks, these trailing arm brackets have the lowest mounting hole position possible. 4.0″ from axle tube to center of hole.
(Sold as a Pair)
Add to cartQuick View
