- Description
- Reviews (0)
Description
This caliper mount brackets is built to fit the small GM metric calipers.
Made out of 1/2″ thick steel to gain extra LR weight.
(Sold Individually)
Be the first to review “Bracket, Caliper (Small GM) HEAVY (LR)” Cancel reply
You may also like…
-
Add to cartQuick View
Bolt On, Caliper Bracket (Small GM) – HEAVY LR (MAXIMUM)
Bolt On, Caliper Bracket (Small GM)
Add to cartQuick View -
Add to cartQuick View
Bolt On, Caliper Bracket – Small GM (MAXIMUM)
Bolt On, Caliper Bracket (Small GM)
Add to cartQuick View -
Add to cartQuick View
Bracket, Caliper (Small GM)
These caliper mount brackets are built to fit the small GM metric calipers. Use this kit to build your own custom rear end.
(Sold Individually)Add to cartQuick View
Related Products
-
Add to cartQuick View
Brackets, Trailing Arm (Single Hole)
Designed for the Wissota street stocks, these trailing arm brackets have the lowest mounting hole position possible. 4.0″ from axle tube to center of hole.
(Sold as a Pair)
Add to cartQuick View -
Add to cartQuick View
Quick Change Mount, Upper Trailing Arm – w/ “PULL” Bushings – Metric (MAXIMUM)
This bolt on upper trailing arm mount is designed to allow use of a quick change into a stock GM metric chassis. Built with corrected pinion angle and our proven “Pull” Bushings.
NOTE: If installing on a Frankland quick change, the bracket will need to be modified and reinforced to fit.
Add to cartQuick View -
Add to cartQuick View
Bracket, Caliper (Small GM)
These caliper mount brackets are built to fit the small GM metric calipers. Use this kit to build your own custom rear end.
(Sold Individually)Add to cartQuick View -
Add to cartQuick View
Axles, Non-Floater 30″, 5×5, (28 or 31 Spline)
These new Superior 28 or 31-spline axles feature screw in studs in a 5×5 wheel bolt pattern, , ¼ thick heavy duty bearing retainer plates, and tapered wheel bearings pressed on.
Add to cartQuick View -
Add to cartQuick View
Rear End Brace Kit – 60″
This kit is design to reinforce the rear end so that the tubes do not bend if a wheel gets wrecked.
It will also prevent the rear end from deflecting under load and changing the alignment of the rear end while braking and under gas.(USRA Legal)
Add to cartQuick View -
Add to cartQuick View
Brackets, Trailing Arm (Multi-Hole)
This trailing arm bracket kit was designed to allow trailing arm angle adjustments just like what can be done on modifieds…..
(Sold as a Pair)
Add to cartQuick View -
Add to cartQuick View
Mount, Upper Trailing Arm – Kit (Ford 9″)
This kit includes two “Pull” bushings, two steel spools, a rectangular mount tube and side gusset bracket. Use this kit to build your own custom rear end.
Add to cartQuick View -
Add to cartQuick View
Cup, Spring – Tapered
These tapered profile spring cups are manufactured from high strength steel and are designed to minimize any stretch and bending while still being lightweight. Has a 1/4″ hole on bottom to allow bolting to your weight jack bolt.
Add to cartQuick View -
Add to cartQuick View
Assembly, Rear End Housing – 60″ GN (L3) w/ Sport Mod Jigged
60″ offset new reproduction stamping Ford 9″ housing with new 3″ tubes and GN hub type snouts. Housings have fill and drain plug installed. Kit includes standard 5×5 GN hubs, hub bearings, seals, brake rotor, drive flange, 31 spline solid axles and all hardware necessary.
Spring Perchs & Brake Caliper Brackets are now Bolt-On Accessories (not included in Rear End Assembly Price)
Add to cartQuick View -
Add to cartQuick View
Bushing, “PULL” (Trailing Arms)
This is a new bushing that is used in the upper & lower trailing arms to create side bite and cushioning of the rear end.
Sold individually
Add to cartQuick View
Reviews
There are no reviews yet.