Bolt On, Trailing Arm Bracket Kit – Extreme Drop (MAXIMUM)
$174.66
Bolt On, Trailing Arm Bracket Kit Extreme Drop LR
- Description
Description
Split trailing arm bracket design to allow installing without removing hubs onto 3” axle tube. Specifically designed to increase LR drive off the corner and corner entry adjustability with multiple hole adjustments on the RR. LR bracket is 6.75″ from axle tube to center of bottom hole. (USRA/IMCA Stock Car Legal)
(Sold as a Pair)
**Trailing arm bracket MUST be welded to rear end housing to keep from rotating**
You may also like…
-
Select optionsQuick ViewQuick Change Rear End – Bare
$2,970.00Quick Change Rear End With 486 R&P 10″ Alum Spool and Steel Tubes.
Select optionsQuick View -
Add to cartQuick ViewBolt On, Spring Perch – Center (MAXIMUM)
$45.86Bolt On, Spring Perch Center
Add to cartQuick View -
Add to cartQuick ViewBolt On, Caliper Bracket – Small GM (MAXIMUM)
$65.00Bolt On, Caliper Bracket (Small GM)
Add to cartQuick View -
Add to cartQuick ViewBolt On, Spring Perch – Offset (MAXIMUM)
$45.86Bolt On, Spring Perch Offset
Add to cartQuick View -
Select optionsQuick ViewQuick Change Rear End – Assembly
$3,950.00Quick Change Rear End Assembly 10″ Alum Spool and Steel Tubes
Select optionsQuick View -
Add to cartQuick ViewBolt On, Trailing Arm Bracket Kit – Multi Hole (MAXIMUM)
$146.66Bolt On, Trailing Arm Bracket Kit Multi Hole
Add to cartQuick View -
Add to cartQuick ViewQuick Change Mount, Upper Trailing Arm – w/ “PULL” Bushings – Metric (MAXIMUM)
$125.50This bolt on upper trailing arm mount is designed to allow use of a quick change into a stock GM metric chassis. Built with corrected pinion angle and our proven “Pull” Bushings.
NOTE: If installing on a Frankland quick change, the bracket will need to be modified and reinforced to fit.
Add to cartQuick View
Related Products
-
Add to cartQuick ViewBRACKET, CHASSIS PANHARD, BOLT ON – 3 INCH OFFSET (PAIR)
$50.00BRACKET, CHASSIS PANHARD, BOLT ON – 3 INCH OFFSET (PAIR)
Add to cartQuick View -
Add to cartQuick ViewBushing, “PULL” (Trailing Arms)
$35.75This is a new bushing that is used in the upper & lower trailing arms to create side bite and cushioning of the rear end.
Sold individually
Add to cartQuick View -
Add to cartQuick ViewHousing, Rear End – 60″ GN (L3) w/ Sport Mod Jigged
$901.3860″ offset new reproduction stamping Ford 9″ housing with new 3″ tubes and GN hub type snouts. Housings have fill and drain plug installed. SportMod jigged.
Spring Perchs & Brake Caliper Brackets are now Bolt-On Accessories (not included in Rear End Housing Price)
(IMCA Legal)
Custom Part is Non-Returnable and Non-Refundable.
Add to cartQuick View -
Add to cartQuick ViewTrailing Arm, Upper – BAREBONE (MAXIMUM)
$65.00Want a stronger trailing arm at a better price? We proudly give you the “BAREBONE”!
Same length and weight of a stock trailing arm but much stronger. Will accept any OEM type bushing.
(Sold Individually)
Add to cartQuick View -
Add to cartQuick ViewWasher, Axle
$5.60Stop spending big money on rubber seals and sleeves to stop rear end grease from being pulled into the RH rear end tube. Sold as pair.
Add to cartQuick View -
Add to cartQuick ViewBolt, Weight Jack – 11″ Long
$21.991 diameter x 11 long weight jack bolt. (1″-8 Coarse Thread)
Add to cartQuick View -
Add to cartQuick ViewAxle, 29.5″ GN Gun Drilled (31 Spline)
$199.5029.5″ Premium GN gun drilled axle.
Add to cartQuick View -
Add to cartQuick ViewPerch, Spring Kit (Offset or Centered)
$31.98Strong, simple and lightweight spring perches that you can use to build your custom rear end. (sold as a pair)
Add to cartQuick View -
Add to cartQuick ViewTrailing Arm, Upper – OEM Reproduction w/ “Pull” Bushing
$132.50For those of you that want the benefits of the “Pull” bushing but without the hassle of installing them.
OEM reproduction stampings with our bushings installed. Sized for use with a 1/2″ bolt. These are a bolt in ready unit.
(Sold Individually)
Add to cartQuick View -
Add to cartQuick ViewTrailing Arm, Upper – DOGBONE w/ “Pull” Bushing (MAXIMUM)
$109.50Want a stronger trailing arm plus the performance advantage of the “Pull” bushing? We proudly give you the “DOGBONE”!
Same length (11-1/8″ C to C) and weight of a stock trailing arm but much stronger. Has “Pull” bushings installed, sized for 1/2″ bolts and is a bolt in ready unit.
(Sold Individually)Add to cartQuick View
