-
Add to cartQuick ViewPerch, Spring Kit (Offset or Centered)
$31.98Strong, simple and lightweight spring perches that you can use to build your custom rear end. (sold as a pair)
Add to cartQuick View -
Add to cartQuick ViewPITMAN ARM (68-72 GM)
$59.99Pitman arm for 800 series power steering boxes. For 1964-72 chevelle steering systems.
- 5.00″ Center to Center, 1.21″ Hole Diameter, 0.75″ Drop
- 32 and 4 master Spline Count
- Forged steel construction for maximum strength
- Spline size fits GM 800 series power steering boxes
Add to cartQuick View -
Add to cartQuick ViewPITMAN ARM (78-88 GM METRIC)
$59.99Pitman arm for 800 series power steering boxes. For 1978-1988 G body steering systems.
- 6.50″ Center to Center
- 32 and 4 master Spline Count
- Forged steel construction for maximum strength
- Spline size fits GM 800 series power steering boxes
Add to cartQuick View -
Add to cartQuick ViewPlate, Hood Pin Mount
$2.24These aluminum hood pins plates are thicker to provide increased durability versus the thin steel ones normally found in kits. Sized for ½ diameter hood pin. (Sold as pair)
Add to cartQuick View -
Add to cartQuick ViewPLATE, HUB COVER – FRONT HUBS WINTERS (MOD LITE)
$25.00Aluminum plate front hub covers for Winters 4 x 4 hubs.
(Sold individually)
Add to cartQuick View -
Add to cartQuick ViewPlates, 4 Link LH – Modified Chassis
$50.00Replacement LH four link plates used on Medieval modified chassis.
Qty 2, sold as pair
Used for A-Mods, B-Mods, MWM, Limited Mods
Add to cartQuick View -
Add to cartQuick ViewPlates, 4 Link RH – Modified Chassis
$50.00Replacement RH four link plates used on Medieval modified chassis.
Qty 2, sold as pair
Used for A-Mods, B-Mods, MWM, Limited Mods
Add to cartQuick View -
Add to cartQuick ViewPlates, Bumper Mount
$11.20These bumper mount plates can be welded to your chassis to allow the use of our bumpers. (Sold as pair)
Add to cartQuick View -
Add to cartQuick ViewPower Steering Mount (Mod Lite)
$54.95Power Steering Hanger Mount – Used on Medieval Mod Lites
Add to cartQuick View -
Add to cartQuick ViewPRE-LOAD BEARING SPACER – GM METRIC
$58.99Allows your front hubs to be tight with minimal drag and side pre-load
Add to cartQuick View -
Add to cartQuick ViewPullbar Bolt Adjuster Kit (Medieval)
$75.00Easily and accurately adjust your pullbar position with this nut and bolt assembly. Simply turn the fine thread bolt and the pullbar will move side to side accordingly. No more removing spacers. ¾” Diameter x 6” long
Add to cartQuick View -
Add to cartQuick ViewQUARTER PANEL-LOWER, 2-PIECE, FABRICATED – LEFT (STOCK CAR)
$120.00This fully fabricated rear quarter panels works for most all style stock car bodies. Does have double bend lower monte carlo lines in it, perfect for meshing with our fabricated door panels.
Body Panels only available for LTL Shipping or Pickup
Add to cartQuick View -
Add to cartQuick View
QUARTER PANEL-LOWER, 2-PIECE, FABRICATED – RIGHT (STOCK CAR)
$120.00This fully fabricated rear quarter panels works for most all style stock car bodies. Does have double bend lower monte carlo lines in it, perfect for meshing with our fabricated door panels.
Body Panels only available for LTL Shipping or Pickup
Add to cartQuick View -
Add to cartQuick ViewQUARTER PANEL-UPPER, 88 MONTE, FABRICATED – LEFT (STOCK CAR)
$75.00This fully fabricated upper quarter panel for 88 monte bodies. Perfect for meshing with our 2 piece fabricated lower quarter panels.
Add to cartQuick View -
Add to cartQuick ViewQUARTER PANEL-UPPER, 88 MONTE, FABRICATED – RIGHT (STOCK CAR)
$75.00This fully fabricated upper quarter panel for 88 monte bodies. Perfect for meshing with our 2 piece fabricated lower quarter panels.
Add to cartQuick View -
Add to cartQuick ViewQuick Adjust Puck – 1/2″ ID
$5.00Quick adjust puck for suspension cages.
Add to cartQuick View -
Add to cartQuick ViewQuick Change Mount, Upper Trailing Arm – NO Bushings – Metric (MAXIMUM)
$105.80This bolt on upper trailing arm mount is designed to allow use of a quick change into a stock GM metric chassis. Built with corrected pinion angle. NO Bushings included.
NOTE: If installing on a Frankland quick change, the bracket will need to be modified and reinforced to fit.
Add to cartQuick View -
Add to cartQuick ViewQuick Change Mount, Upper Trailing Arm – w/ “PULL” Bushings – Metric (MAXIMUM)
$125.50This bolt on upper trailing arm mount is designed to allow use of a quick change into a stock GM metric chassis. Built with corrected pinion angle and our proven “Pull” Bushings.
NOTE: If installing on a Frankland quick change, the bracket will need to be modified and reinforced to fit.
Add to cartQuick View -
Add to cartQuick ViewQuick Change Mount, Upper Trailing Arm – w/ “SPHERICAL” Bushings – Metric (MAXIMUM)
$166.99This bolt on upper trailing arm mount is designed to allow use of a quick change into a stock GM metric chassis. Built with corrected pinion angle and our proven “Spherical” Bushings.
NOTE: If installing on a Frankland quick change, the bracket will need to be modified and reinforced to fit.
Add to cartQuick View -
Add to cartQuick ViewQuick Change Mount, Upper Trailing Arm – ZERO DEGREE Pinion Angle & “PULL” Bushings – Metric (MAXIMUM)
$125.50This bolt on upper trailing arm mount is designed to allow use of a quick change into a stock GM metric chassis.
Built with ZERO degrees of pinion angle and our proven “Pull” Bushings.
Perfect for southern sport mods!
NOTE: If installing on a Frankland quick change, the bracket will need to be modified and reinforced to fit.
Add to cartQuick View -
Add to cartQuick ViewQuick Change Pull Bar Mount – Forward
$45.00Add to cartQuick View -
Add to cartQuick ViewQuick Change Pull Bar Mount – Standard (MAXIMUM)
$55.00Add to cartQuick View -
Select optionsQuick ViewQuick Change Rear End – Assembly
$3,950.00Quick Change Rear End Assembly 10″ Alum Spool and Steel Tubes
Select optionsQuick View -
Select optionsQuick ViewQuick Change Rear End – Assembly With Bolt On Suspension Kit
$3,337.88 – $3,504.32Quick Change Rear End Assembly With Bolt On Suspension Kit
Select optionsQuick View -
Select optionsQuick ViewQuick Change Rear End – Bare
$2,970.00Quick Change Rear End With 486 R&P 10″ Alum Spool and Steel Tubes.
Select optionsQuick View -
Select optionsQuick ViewQuick Change Rear End – Bare With Bolt On Suspension Kit
$2,638.26 – $3,645.46Quick Change Rear End With Bolt On Suspension Kit
Select optionsQuick View -
Add to cartQuick ViewQUICK CHANGE REAR END ASSY, 7″, BABY GRAND, 46″ FLANGE TO FLANGE W/ 7″ OFFSET RH (WINTERS)
$3,417.78QUICK CHANGE REAR END ASSY, 7″, BABY GRAND – MOD LITE
Add to cartQuick View -
Add to cartQuick ViewQUICK RELEASE – SPLINED (TITAN 22400)
$65.49Splined quick release assemblies create a tighter fit with less slop for the steering wheel. This will allow for more precise steering input without lag.
- All Aluminum Hub
- Black Anodized finish
- Steel Spline that fits 3/4″ Round Steering Column Tubing
- Comes with mounting hardware to attach steering wheel
Add to cartQuick View -
Add to cartQuick ViewQUICKCAR, 2 – 1 Gauge Panel – 5″ Tach- OP/WH BK
$389.95QuickCar’s LED backlit Oil Pressure, 5” Tachometer, and Water Temperature standard mechanical gauges mounted in a black panel measuring 11-7/8” wide and 4-1/2” tall. Panel comes complete with all sending units, warning lights, and wiring for easy installation. Water Temp. gauge comes with a 1/2”-NPT adapter to mount in the intake of almost any high-performance engine while Oil Pressure has a standard 1/8”-NPT fitting for plumbing lines (sold separately). Tachometer has a 5” display from 0-10,000 RPM’s with a single high recall and can be used with a 4-cylinder, 6-cylinder, or V8 engine. Warning lights activate when Oil Pressure drops below 20 PSI, Water Temp. goes above 235°F.
Add to cartQuick View -
Add to cartQuick ViewQUICKCAR, 2 – 1 GAUGE PANEL – OP/WT/TACH
$389.95QuickCar’s LED backlit Oil Pressure, 5” Tachometer, and Water Temperature standard mechanical gauges mounted in a checkered flag designed panel measuring 11-7/8” wide and 4-1/2” tall. Panel comes complete with all sending units, warning lights, and wiring for easy installation. Water Temp. gauge comes with a 1/2”-NPT adapter to mount in the intake of almost any high-performance engine while Oil Pressure has a standard 1/8”-NPT fitting for plumbing lines (sold separately). Tachometer has a 5” display from 0-10,000 RPM’s with a single high recall and can be used with a 4-cylinder, 6-cylinder, or V8 engine. Warning lights activate when Oil Pressure drops below 20 PSI, Water Temp. goes above 235°F.
Add to cartQuick View -
Add to cartQuick ViewQUICKCAR, Gauge Wiring Harness Kit
$27.95This QuickCar 5 Foot Four Wire Ignition and Accessory Wiring Harness is for use with cars using a remote Ignition Box such as an MSD or FAST system.
Add to cartQuick View -
Add to cartQuick ViewQUICKCAR, Ignition Panel w/ Flip Switch And Light
$54.95This QuickCar Switch Panel comes with 1 ignition switch and 1 starter button installed in a checkered flag designed plate. The double pole ignition switch is covered with a red flip cover and has a red indicator light. The panel dimensions are 3-3/8″ wide and 4-1/4″ tall. Panel comes assembled and pre-wired with mounting holes already punched out to make installation simple.
Add to cartQuick View -
Add to cartQuick ViewQUICKCAR, Ignition Panel w/ Flip Switch and Light
$54.95This QuickCar Switch Panel comes with 1 ignition switch and 1 starter button installed in a checkered black plate. The double pole ignition switch is covered with a red flip cover and has a red indicator light. The panel dimensions are 3-3/8″ wide and 4-1/4″ tall.
Add to cartQuick View -
Add to cartQuick ViewQUICKCAR, Master Disconnect Switch
$37.95This QuickCar Battery Master Disconnect Switch comes with a checkered flag square mounting Panel that measures 2-1/2”x2-1/2”
Add to cartQuick View -
Add to cartQuick ViewQUICKCAR, Master Disconnect Switch
$37.95This QuickCar Battery Master Disconnect Switch comes with a black square mounting Panel that measures 2-1/2”x2-1/2”
Add to cartQuick View -
Add to cartQuick ViewQUICKCAR, Mini Brake Bias Gauge (61-105) – Black
$79.95This QuickCar 2-Gauge Panel Kit is Vertical Mount Model that has Two 1,000 PSI Brake Bias Gauges that use 1/8 NPT Male Fittings.
Add to cartQuick View -
Add to cartQuick ViewREAR BODY/TAIL MOUNT – (STOCK CAR)
$28.00Rear body and tail cone mount used on Medieval stock cars.
Add to cartQuick View -
Add to cartQuick ViewREAR END BALLAST MOUNT
$44.86Clamp-On Ballast Mount – 3″ Tube
Sold as a Pair
Add to cartQuick View -
Add to cartQuick ViewRear End Brace Kit – 60″
$119.94This kit is design to reinforce the rear end so that the tubes do not bend if a wheel gets wrecked.
It will also prevent the rear end from deflecting under load and changing the alignment of the rear end while braking and under gas.(USRA Legal)
Add to cartQuick View -
Add to cartQuick ViewRear End Brace Kit (Main Bracket Only)
$18.98This is the main bracket for the “Rear End Brace Kits” (sold individually)
Add to cartQuick View -
Add to cartQuick ViewROD END (RH) – 3/4″ OVERSIZED
$14.993/4″ OVERSIZED ROD END USED TO MOUNT STEERING POSTS
Add to cartQuick View -
Add to cartQuick ViewROD END (RH) 5/8″-18 MALE
$9.995/8-18 right hand male standard rod end. They have a carbon steel body and a hardened steel ball.
Add to cartQuick View -
Add to cartQuick ViewROTOR – PROLITE VENTED (11.75 X .810)
$47.99Add to cartQuick View -
Add to cartQuick ViewRotor Assembly (5×5) – 78-88 Metric
$93.99This is an Afco rotor assembly for the 78-88 metric. It has 5/8 studs and a 5×5 bolt pattern.
Add to cartQuick View -
Add to cartQuick ViewROTOR, BRAKE – MOD LITE (9.875 X .25)
$25.00Brake rotor for Winters 4×4 hubs. 1/4″ thick with lightening holes. Mod Lite
(Sold individually)
Add to cartQuick View -
Add to cartQuick ViewRub Rail – Internal (Hobby Stock Straight LH) (2010 to Present)
$84.00Want to have a rub rail that is light, easily replaceable and offers improved protection then these internal rub rails are a must.
Add to cartQuick View -
Add to cartQuick ViewRub Rail – Internal (Hobby Stock Straight RH)-(2018 to Present)
$84.00For use on 2018 to Present Medieval hobby stock. Passenger side ONLY.
Add to cartQuick View -
Add to cartQuick ViewRub Rail – Internal (Stock Car Layback LH) (2011-Present)
$84.00Want to have a rub rail that is light, easily replaceable and offers improved protection then these internal rub rails are a must…..
Add to cartQuick View -
Add to cartQuick ViewRub Rail – Internal (Stock Car Layback RH) (2016-2018)
$84.00Want to have a rub rail that is light, easily replaceable and offers improved protection then these internal rub rails are a must…..
Add to cartQuick View -
Add to cartQuick ViewRub Rail – Internal (Stock Car Layback RH) (2019-2022)
$84.00This rub rail has a 10 degree layback to it. For use on 2019 to 2022 Medieval stock car chassis. (Passenger Side Only)
Add to cartQuick View -
Add to cartQuick ViewRub Rail – Modified (Left Side)
$35.00Rub rail nerf bar for the left side of Medieval chassis.
Add to cartQuick View -
Add to cartQuick ViewRub Rail – Modified (Right Side)
$40.00Rub rail/nerf mount for the right side of Medieval chassis.
Add to cartQuick View -
Add to cartQuick ViewRub Rail – Rear
$22.40Light and strong, these rub rails are designed to be used on the rear frame clip. The radius corners prevent another racer from being able to hook your car with their bumper. (Sold Individually)
Add to cartQuick View -
Add to cartQuick ViewRub Rail – Stock Car (Right Side- Adjustable) (2023-Present)
$40.00This is the passenger side outer rub rail for Medieval stock cars.
Add to cartQuick View -
Add to cartQuick View
Rub Rail – Stock Car (Right Side Lower) (2022-Present)
$35.00Lower right side rub rail for stock cars and hobby stocks.
Add to cartQuick View -
Add to cartQuick ViewRUB RAIL, MOD LITE (LH)
$30.00Rub Rail, LH – Medieval Mod Lite
Add to cartQuick View -
Add to cartQuick ViewRUB RAIL, MOD LITE (RH)
$30.00Rub Rail, RH – Medieval Mod Lite
Add to cartQuick View -
Add to cartQuick ViewScrew Jack Mount, Clamp On – 1 1/2″ Tube (WEHRS)
$60.00Use this clamp on mount for the REAR shock mounts on all Medieval.
Uses Shock & Spring Adjuster (1″ coarse) (sold separately)
Add to cartQuick View -
Add to cartQuick ViewSeal, Axle Housing (Inner)
$61.99Axle Housing Inner Seal for 9 Inch GN Rearends. Three O-rings that seal it to the axle tube and two bonded, heavy duty inner seals designed to compensate for any amount of axle shaft run out. Keeps gear oil in the center section. 2.625″ Housing Tube Size.
Add to cartQuick View -
Add to cartQuick ViewSEAL, GN HUB SEAL 3X3.75X.38
$11.99GN Hub Seal. Used on inside of all standard GN hubs.
Add to cartQuick View
Products
