Quick Change Rear End – Bare
$2,129.24
Quick Change Rear End With 486 R&P 10″ Alum Spool and Steel Tubes.
- Description
- Additional information
Description
STANDARD FEATURES
• Magnesium/Aluminum Construction
• Heat Treated Lower Shaft
• Roller Pinion Nose Bearing
• Lightened Full Spool
• REM Finished Ring & Pinion, Bearings and Races
Rear End Ratio Ring & Pinion Options: 486 or 411
Additional information
| Ratio Ring & Pinion | 486, 411 |
|---|
You may also like…
-
Add to cartQuick ViewBolt On, Trailing Arm Bracket Kit – Multi Hole (MAXIMUM)
$146.66Bolt On, Trailing Arm Bracket Kit Multi Hole
Add to cartQuick View -
Add to cartQuick ViewBolt On, Caliper Bracket – Small GM (MAXIMUM)
$65.00Bolt On, Caliper Bracket (Small GM)
Add to cartQuick View -
Add to cartQuick ViewBolt On, Spring Perch – Center (MAXIMUM)
$45.86Bolt On, Spring Perch Center
Add to cartQuick View -
Add to cartQuick ViewQuick Change Mount, Upper Trailing Arm – w/ “PULL” Bushings – Metric (MAXIMUM)
$125.50This bolt on upper trailing arm mount is designed to allow use of a quick change into a stock GM metric chassis. Built with corrected pinion angle and our proven “Pull” Bushings.
NOTE: If installing on a Frankland quick change, the bracket will need to be modified and reinforced to fit.
Add to cartQuick View -
Add to cartQuick ViewBolt On, Trailing Arm Bracket Kit – Extreme Drop (MAXIMUM)
$174.66Bolt On, Trailing Arm Bracket Kit Extreme Drop LR
Add to cartQuick View -
Select optionsQuick ViewBolt On, Suspension Kit
$509.02 – $675.46Bolt On Suspension Kit Stock Car
Select optionsQuick View -
Add to cartQuick ViewTrailing Arm, Upper – DOGBONE w/ “Pull” Bushing (MAXIMUM)
$109.50Want a stronger trailing arm plus the performance advantage of the “Pull” bushing? We proudly give you the “DOGBONE”!
Same length (11-1/8″ C to C) and weight of a stock trailing arm but much stronger. Has “Pull” bushings installed, sized for 1/2″ bolts and is a bolt in ready unit.
(Sold Individually)Add to cartQuick View -
Add to cartQuick ViewBolt On, Spring Perch – Offset (MAXIMUM)
$45.86Bolt On, Spring Perch Offset
Add to cartQuick View
Related Products
-
Add to cartQuick View
Trailing Arm, Upper – DOGBONE w/ “Pull” Bushing (MAXIMUM)
$109.50Want a stronger trailing arm plus the performance advantage of the “Pull” bushing? We proudly give you the “DOGBONE”!
Same length (11-1/8″ C to C) and weight of a stock trailing arm but much stronger. Has “Pull” bushings installed, sized for 1/2″ bolts and is a bolt in ready unit.
(Sold Individually)Add to cartQuick View -
Add to cartQuick ViewAxle, 32″ GN Gun Drilled (31 Spline)
$199.5029.5″ Premium GN gun drilled axle.
Add to cartQuick View -
Add to cartQuick ViewBushing, “SPHERICAL” – Trailing Arm (MAXIMUM)
$44.95MAXIMUM Spherical Bushing
Sold individually
Add to cartQuick View -
Add to cartQuick ViewWasher, Axle
$5.60Stop spending big money on rubber seals and sleeves to stop rear end grease from being pulled into the RH rear end tube. Sold as pair.
Add to cartQuick View -
Add to cartQuick ViewQuick Change Mount, Upper Trailing Arm – w/ “SPHERICAL” Bushings – Metric (MAXIMUM)
$166.99This bolt on upper trailing arm mount is designed to allow use of a quick change into a stock GM metric chassis. Built with corrected pinion angle and our proven “Spherical” Bushings.
NOTE: If installing on a Frankland quick change, the bracket will need to be modified and reinforced to fit.
Add to cartQuick View -
Add to cartQuick ViewBolt, Weight Jack – 11″ Long
$21.991 diameter x 11 long weight jack bolt. (1″-8 Coarse Thread)
Add to cartQuick View -
Add to cartQuick ViewTrailing Arm, Upper – OEM Reproduction w/ “Pull” Bushing
$132.50For those of you that want the benefits of the “Pull” bushing but without the hassle of installing them.
OEM reproduction stampings with our bushings installed. Sized for use with a 1/2″ bolt. These are a bolt in ready unit.
(Sold Individually)
Add to cartQuick View -
Add to cartQuick View
Axle, 29.5″ GN Gun Drilled (31 Spline)
$199.5029.5″ Premium GN gun drilled axle.
Add to cartQuick View -
Add to cartQuick ViewBrackets, Trailing Arm (Multi-Hole)
$84.00This trailing arm bracket kit was designed to allow trailing arm angle adjustments just like what can be done on modifieds…..
(Sold as a Pair)
Add to cartQuick View -
Add to cartQuick ViewHousing, Rear End – 60″ GN (L3) w/ Sport Mod Jigged
$901.3860″ offset new reproduction stamping Ford 9″ housing with new 3″ tubes and GN hub type snouts. Housings have fill and drain plug installed. SportMod jigged.
Spring Perchs & Brake Caliper Brackets are now Bolt-On Accessories (not included in Rear End Housing Price)
(IMCA Legal)
Custom Part is Non-Returnable and Non-Refundable.
Add to cartQuick View
